ISO-11093-6-2005.pdf
《ISO-11093-6-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-11093-6-2005.pdf(10页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11093-6:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 11093-6 Second edition 2005-05-01 Paper and board Testing of cores Part 6: Determination of bending strength by the three-point method Papier et carton Essais des mandrins Partie 6: Dtermination de la rsistance la flexion par
2、la mthode des trois points Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:19:51 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11093-6:2005(E)
3、PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
4、parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relat
5、ive to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 20
6、05 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the cou
7、ntry of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under l
8、icense with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:19:51 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11093-6:2005(E) ISO 2005 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a wor
9、ldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on
10、 that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted
11、in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standar
12、d requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11093-6 was prepared by
13、 Technical Committee ISO/TC 6, Paper, board and pulps. This second edition cancels and replaces the first edition (ISO 11093-6:1996), which has been technically revised. ISO 11093 consists of the following parts, under the general title Paper and board Testing of cores: Part 1: Sampling Part 2: Cond
14、itioning of test samples Part 3: Determination of moisture content using the oven drying method Part 4: Measurement of dimensions Part 5: Determination of characteristics of concentric rotation Part 6: Determination of bending strength by the three-point method Part 7: Determination of flexural modu
15、lus by the three-point method Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis Part 9: Determination of flat crush resistance Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standard
16、s 1/9972545001 Not for Resale, 04/24/2007 19:19:51 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:19
17、:51 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 11093-6:2005(E) ISO 2005 All rights reserved 1 Paper and board Testing of cores Part 6: Determination of bending strength by the three-point method 1 Scope This part of ISO 11093 specifies a thre
18、e-point method for the determination of the bending strength of cylindrical board cores which meet the following criteria: internal diameter: 50 mm to 300 mm; minimum wall thickness: 5 mm; minimum test length of core (span): 1 100 mm. 2 Normative references The following referenced documents are ind
19、ispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Ten
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11093 2005
链接地址:https://www.31doc.com/p-3774099.html