ISO-11093-1-1994.pdf
《ISO-11093-1-1994.pdf》由会员分享,可在线阅读,更多相关《ISO-11093-1-1994.pdf(8页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 11093-1 First edition 1994-12-15 Paper and board - Testing of cores - Part 1: Sampling Papier et carton - Essais des mandrins - Partie 7 : khan tillonnage Reference number ISO 11093-1 :1994(E) Copyright International Organization for Standardization Provided by IHS under l
2、icense with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 01:36:11 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11093=1:1994(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Sta
3、ndards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International or
4、ganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are
5、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 11093-1 was prepared by Technical Committee lSO/TC 6, Paper, board and pulps, Subcommittee SC 3, Dimensions and gra
6、mmage of Paper, board and pulp products. ISO 11093 consists of the following Parts, under the general title Paper and board - Testing of cores: - Part 1: Sampling - Part 2: Conditioning of test samples - Part 3: Determination of moisture content using the oven drying method - Part 4: Dimensional mea
7、suremen ts - Part 5: Determination of characteristics of concentric rotation - Part 8: Machine test for dynamic cleavage - Part 9: Determination of flat crush resistance 0 ISO 1994 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
8、or by any means, electronie or mechanical, including photocopying and microfilm, without Permission in writing from the publisher. lnternational Organization for Standardization Case postale 56 l CH-l 211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Stan
9、dardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 01:36:11 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD o ISO ISO 11093-1:1994(E) Paper and board - Testing of cores - Part 1
10、: Sampling 1 Scope This part of ISO 11093, based on ISO 186:1994, Paper and board - Sampling to determine average quality, specifies a method for obtaining a representative Sample of a lot of cores for test purposes. NOTE 1 If less than 50 % of the tot is available for sampling, then sampling will b
11、e invalid in the absence of agreement to the contrary. 2 Definitions For the purposes of this part of ISO 11093, the following definitions apply. 2.1 lot: Aggregate of cores of a Single kind possessing specified characteristics. A lot may comprise one or more identical packaged units. 2.2 specimen:
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11093 1994
链接地址:https://www.31doc.com/p-3774108.html