ISO-11106-1-1997.pdf
《ISO-11106-1-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-11106-1-1997.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 111064 First edition 1997-03-01 Photography - Slide trays for projectors - Part 1: Straight slide tray, open type (European design) Photographie - Paniers chargeurs de diapositives pour projecteurs - Partie I: Panier chargeur droit de diapositives, type ouver? (conception
2、europbenne) Fe - - - - -lsoi - - - - - - - a=400net; p=iso; o=isocs; s=central Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 19:41:54 MDTNo reproducti
3、on or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 IS0 11106-l :1997(E) Photography - Slide trays for projectors - Part 1: Straight slide tray, open type (European design) 1 Scope This part of IS0 11106 specifies the essential dimensions of a straight slide tray, op
4、en type (European design), for projector slides of the preferred international nominal size 5 cm x 5 cm complying with IS0 1755, with a capacity of 36 slides or 50 slides. It includes a testing gauge for checking the tray profile and gear system. In this design, the slide tray is placed upright into
5、 the projector and the slides are lifted approximately 9 mm out of the tray and then pushed sideways into the projector. Slides remain fully accessible when the tray is inserted in the projector and can be removed and reinserted. This part of IS0 11106 is intended to facilitate the manufacture, use
6、and interchangeability of straight slide trays in different slide projectors which are designed for this type of tray. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 11106. At the time of publication,
7、 the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 11106 are encouraged to investigate the possibility of applying the most recent edition of the standards indicated below. Members of IEC and IS0 maintain registers of curren
8、tly valid International Standards. IS0 53:1974, Cylindrical gears for general and heavy engineering - Basic rack. IS0 1622-l :I 994, Plastics - Polystyrene (PS) moulding and extrusion materials - Part I: Designation system and basis for specifications. IS0 1755: 1987, Photography - Projector slides
9、- Dimensions. IS0 2768-1 :I 989, Genera/ tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications. 3 Capacity The capacity of the straight slide tray, open type, shall be either 36 slides or 50 slides. 4 Dimensions 4.1 Details which are not mentioned
10、 should be selected in accordance with their purpose. Dimensions without tolerance indications are in accordance with IS0 2768-1 (tolerance class: medium). 4.2 The spacing dimension 5,5 + 0,05 mm determines the distance between the centres of the tooth spaces for the two-toothed racks and the distan
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11106 1997
链接地址:https://www.31doc.com/p-3774125.html