ISO-11087-2004.pdf
《ISO-11087-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-11087-2004.pdf(16页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11087:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 11087 Second edition 2004-03-01 Alpine ski-bindings Retention devices Requirements and test methods Fixations de skis alpins Dispositifs de retenue Exigences et mthodes dessai Copyright International Organization for Standardiza
2、tion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11087:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with A
3、dobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing poli
4、cy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every c
5、are has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication m
6、ay be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel
7、. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04
8、/21/2007 00:43:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11087:2004(E) ISO 2004 All rights reserved iii Contents Page Forewordiv 1 Scope1 2 Normative references .1 3 Terms and definitions.1 4 Requirements 2 5 Test methods.2 6 Instruction for use.8 Annex A (norm
9、ative) Binding straps9 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11087:2004(E) iv ISO
10、 2004 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested
11、in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commi
12、ssion (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technica
13、l committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shal
14、l not be held responsible for identifying any or all such patent rights. ISO 11087 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment, Subcommittee SC 3, Ski bindings. This second edition cancels and replaces the first edition (ISO 11087:1997), which has been technicall
15、y revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:38 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 11087:200
16、4(E) ISO 2004 All rights reserved 1 Alpine ski-bindings Retention devices Requirements and test methods 1 Scope This International Standard specifies the requirements for ski brakes and binding straps. It applies to alpine retention devices which are used to reduce the risk of injury, caused by the
17、ski after the skis release. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies
18、. ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications ISO 5355:1997, Alpine ski-boots Safety requirements and test methods ISO 6289:2003, Skis Vocabulary ISO 8364:1999, Alpine skis and bindings Binding mounting area Requirements and test methods ISO 9462:1993, Alpine sk
19、i-bindings Safety requirements and test methods ISO 9838:1991, Alpine ski-bindings Test soles for ski-binding tests 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 ski brake retention device for alpine skiing which is integrated into the ski
20、binding and which is designed to slow down a ski which has come off after the release of a ski binding NOTE Integrated ski brakes represent the state of the art. 3.2 course of fall area that can be passed over by a skier after a fall, the length of which corresponds to the braking distance of the sk
21、ier measured between the point of fall and the stoppage, the width of the area being assumed to be approximately 5 m Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:38 MDTN
22、o reproduction or networking permitted without license from IHS -,-,- ISO 11087:2004(E) 2 ISO 2004 All rights reserved 4 Requirements 4.1 Compatibility with binding function The ski brakes shall comply with the requirements in ISO 9462 and ISO 5355 which are relevant for ski brakes. 4.2 Interference
23、 with skiing The ski brake shall not interfere with skiing. It shall be designed to prevent a catching of the ski or a skidding due to premature contact of the ski brake with the slope during skiing, even in steep terrain. During skiing, the ski brake shall not switch into the braking position witho
24、ut the need to do so. 4.3 Mechanical stability The design of the ski brake shall be able to withstand, without damage, the loads occurring in practice. 4.4 Functional reliability Cold, snow and icing shall not interfere with the proper release of the ski brake. 4.5 Automatic function The ski brake s
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11087 2004
链接地址:https://www.31doc.com/p-3774147.html