ISO-11111-7-2005.pdf
《ISO-11111-7-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-11111-7-2005.pdf(42页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11111-7:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 11111-7 First edition 2005-02-15 Textile machinery Safety requirements Part 7: Dyeing and finishing machinery Matriel pour lindustrie textile Exigences de scurit Partie 7: Machines de teinture et de finissage Copyright Interna
2、tional Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/11/2007 04:03:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11111-7:2005(E) PDF disclaimer This PDF file may contain embedded typefaces.
3、In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing A
4、dobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized f
5、or printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part o
6、f this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 C
7、H-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale,
8、 04/11/2007 04:03:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11111-7:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword.v Introduction .vi 1 Scope1 2 Normative references .1 3 Terms and definitions.2 4 List of significant hazards2 5 Significant haza
9、rds and corresponding safety requirements and/or measures2 5.1 General.2 5.2 Preparation machines and equipment2 5.2.1 Common requirements for preparation machines and equipment2 5.2.2 Brushing machines.3 5.2.3 Cropping machines, shearing machines3 5.2.4 Slitting machines 4 5.2.5 Singeing machines .
10、5 5.2.6 Desizing (scouring) machines.6 5.2.7 Discontinuous bleaching plants (open kiers)6 5.2.8 Bleaching pits7 5.2.9 Continuous bleaching plants.7 5.2.10 Washers .8 5.2.11 Autoclaves.9 5.2.12 Continuous steamers for fabric.9 5.2.13 J-boxes.11 5.2.14 Mercerizing equipment.11 5.2.15 Crabbing machines
11、.12 5.2.16 Milling machines .12 5.3 Dyeing machines and apparatus.13 5.3.1 Common requirements for dyeing machines and apparatus.13 5.3.2 Atmospheric dyeing machines and apparatus13 5.3.3 High temperature dyeing machines and apparatus 14 5.3.4 Liquor preparation plants for dyeing processes.16 5.3.5
12、Jigs.17 5.3.6 Winches17 5.3.7 Jet dyeing machines.18 5.3.8 Padding mangles 18 5.3.9 Continuous dyeing machines19 5.3.10 Package dyeing apparatus.19 5.3.11 Beam dyeing apparatus20 5.3.12 Hank dyeing machines.20 5.4 Printing machines.20 5.4.1 Common requirements for printing machines.20 5.4.2 Flat scr
13、een printing machines.21 5.4.3 Rotary screen printing machines21 5.4.4 Transfer printing machines21 5.4.5 Roller printing machines21 5.4.6 Colour paste preparation plant22 5.5 Fixation, wetting and drying machines.23 5.5.1 Common requirements for fixation, wetting and drying machines.23 5.5.2 Steam
14、chambers .23 5.5.3 Wringing machines.23 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/11/2007 04:03:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11111-7:2005(E) iv I
15、SO 2005 All rights reserved 5.5.4 Stenters, tenters24 5.5.5 Dryers, bakers25 5.5.6 Cylinder dryers25 5.5.7 High frequency dryers 26 5.5.8 Straightening machines26 5.6 Finishing machines.27 5.6.1 Common requirements for finishing machines .27 5.6.2 Calenders .27 5.6.3 Calenders for tubular knitted fa
16、bric 28 5.6.4 Coating and laminating machines.29 5.6.5 Raising machines29 5.6.6 Cropping machines and shearing machines30 5.6.7 Shrinking machines 30 5.6.8 Flocking plant31 5.6.9 Decatizing machines.31 5.6.10 Rotary presses.31 5.6.11 Polishing machines.32 5.6.12 Liquor preparation plants for finishi
17、ng processes32 5.7 Making-up/presentation machines33 5.7.1 Common requirements for making-up/presentation machines .33 5.7.2 Inspection machines.34 5.7.3 Folding machines34 6 Verification of the safety requirements and/or measures.34 7 Information concerning machine use .34 Bibliography35 Copyright
18、International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/11/2007 04:03:05 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11111-7:2005(E) ISO 2005 All rights reserved v Foreword ISO (the Inter
19、national Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has
20、been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical st
21、andardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies
22、for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or
23、all such patent rights. ISO 11111-7 was prepared by Technical Committee ISO/TC 72, Textile machinery and machinery for dry- cleaning and industrial laundering, Subcommittee SC 8, Safety requirements for textile machinery. This first edition of ISO 11111-7, together with ISO 11111-1, ISO 11111-2, ISO
24、 11111-3, ISO 11111-4, ISO 11111-5 and ISO 11111-6, cancels and replaces ISO 11111:1995, which has been technically revised. ISO 11111 consists of the following parts, under the general title Textile machinery Safety requirements: Part 1: Common requirements Part 2: Spinning preparatory and spinning
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11111 2005
链接地址:https://www.31doc.com/p-3774191.html