ISO-1163-2-1995.pdf
《ISO-1163-2-1995.pdf》由会员分享,可在线阅读,更多相关《ISO-1163-2-1995.pdf(7页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 I 163-2 Second edition 1995-08-15 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties Plastiques - Poly(chlorure de viny/e) non plastifik (PVC-U) pour moulage et extr
2、usion - Partie 2: Wparation des Bprouvettes et d - use test procedures as specified in this part of IS0 1163. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 1163. At the time of publication, the editi
3、ons indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 1163 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid
4、International Standards. IS0 62:1980, Plastics - Determination of water ab- sorption. IS0 75-l :I 993, Plastics - Determination of tempera- ture of deflection under load - Part 7: General test method. IS0 75-2: 1993, Plastics - Determination of tempera- ture of deflection under load - Part 2: Plasti
5、cs and ebonite. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 03:24:15 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 1163-2:1995(E) Q IS0 IS0
6、178:1993, Plastics - Determination of flexural properties. IS0 179:1993, Plastics - Determination of Charpy impact strength. IS0 291 :1977, Plastics - Standard atmospheres for conditioning and testing. IS0 293:1986, Plastics - Compression moulding test specimens of thermoplastic materials. IS0 306:1
7、994, Plastics - Thermoplastic materials - Determination of Vicat softening temperature IVSTI. IS0 527-1:1993, Plastics - Determination of tensile properties - Part 1: General principles. IS0 527-2:1993, Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusi
8、on p/as tics. IS0 527-4:-l , Plastics - Determination of tensile properties - Pat-t 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites. IS0 899-l :I 993, Plastics - Determination of creep behaviour - Part 1: Tensile creep. IS0 1163-I :A), Plastics - Unplasticized po
9、lyfvinyl chloride) (PVC-U) moulding and extrusion materials - Part 7: Designation system and basis for specifi- cations. IS0 1183:1987, Plastics - Methods for determining the density and relative density of non-cellular plastics. IS0 1210:1992, Plastics - Determination of the burning behaviour of ho
10、rizontal and vertical specimens in contact with a small-flame ignition source. IS0 2818:1994, Plastics - Preparation of test speci- mens by machining. IS0 3167:1993, Plastics - Multipurpose test speci- mens. IS0 45892:-l), Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambie
11、nt- temperature test. IS0 458%3:-l), Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated- temperature test. IS0 8256:1990, Plastics - Determination of tensile- impact strength. IS0 10350:1993, Plastics - Acquisition and presen- ta tion of comparable single-point data. IE
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1163 1995
链接地址:https://www.31doc.com/p-3774193.html