ISO-1132-2-2001.pdf
《ISO-1132-2-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-1132-2-2001.pdf(54页珍藏版)》请在三一文库上搜索。
1、Reference number ISO/FDIS 1132-2:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 1132-2 First edition 2001-09-01 Rolling bearings Tolerances Part 2: Measuring and gauging principles and methods Roulements Tolrances Partie 2: Principes et mthodes de mesurage et de vrification par calibre Copyright Intern
2、ational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 01:59:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1132-2:2001(E) PDF disclaimer This PDF file may contain emb
3、edded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of
4、 not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
5、 were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise spe
6、cified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office
7、Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standa
8、rds 1/9972545001 Not for Resale, 04/07/2007 01:59:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1132-2:2001(E) ISO 2001 All rights reservediii ContentsPage Foreword.iv 1Scope 1 2Normative references1 3Terms and definitions .2 4Symbols2 5General conditions 4 6Measur
9、ing and gauging principles and methods.7 7Principles of measuring bore diameter.8 8Principles of measuring outside diameter14 9Principles of measuring width and height17 10Principles of measuring ring and washer chamfer dimension.24 11Principles of measuring raceway parallelism.26 12Principles of me
10、asuring surface perpendicularity.28 13Principles of measuring thickness variation32 14Principles of measuring radial runout.37 15Principles of measuring axial runout 42 16Principles of measuring radial clearance45 Annex A (normative) Cross-reference to clauses in ISO 1132-147 Copyright International
11、 Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 01:59:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1132-2:2001(E) iv ISO 2001 All rights reserved Foreword ISO (the I
12、nternational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee
13、has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnica
14、l standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by
15、 at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 1132 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1132-2 was pre
16、pared by Technical Committee ISO/TC 4, Rolling bearings. This first edition of ISO 1132-2 cancels and replaces ISO/TR 9274:1991, in the form of a technical revision thereof. ISO 1132 consists of the following parts, under the general title Rolling bearings Tolerances: ?Part 1: Terms and definitions
17、?Part 2: Measuring and gauging principles and methods Annex A forms a normative part of this part of ISO 1132. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 01:59:31 MDTNo repr
18、oduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 1132-2:2001(E) ISO 2001 All rights reserved1 Rolling bearings Tolerances Part 2: Measuring and gauging principles and methods 1Scope This part of ISO 1132 establishes guidelines for measurement of dimensions, r
19、unning accuracy and internal clearance of rolling bearings. The purpose is to outline the fundamentals of various measuring and gauging principles which may be used in order to clarify and comply with the definitions of ISO 1132-1 and ISO 5593. The measuring and gauging methods described in this par
20、t of ISO 1132 may differ amongst themselves and do not provide for a unique interpretation. It is recognized that there are other adequate measuring and gauging methods and that technical development may result in even more convenient methods. Therefore, this part of ISO 1132 does not imply any obli
21、gation to apply any particular method. However, the methods specified may be referred to in cases of dispute. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 1132. For dated references, subseq
22、uent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 1132 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest
23、 edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 1:1975, Standard reference temperature for industrial length measurements. ISO 76:1987, Rolling bearings Static load ratings. ISO 104:1), Rolling bearings
24、 Thrust bearings Boundary dimensions, general plan. ISO 286-2:1988, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts. ISO 1132-1:2000, Rolling bearings Tolerances Part 1: Terms and definitions. ISO 3030:1996, Rolling bearings Radial
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1132 2001
链接地址:https://www.31doc.com/p-3774194.html