ISO-11601-2008.pdf
《ISO-11601-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-11601-2008.pdf(32页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11601:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 11601 Second edition 2008-12-15 Fire fighting Wheeled fire extinguishers Performance and construction Lutte contre lincendie Extincteurs sur roues Performances et construction Copyright International Organization for Standardiza
2、tion Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/31/2009 02:08:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 11601:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing p
3、olicy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Centr
4、al Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been take
5、n to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this p
6、ublication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 G
7、eneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/31/2
8、009 02:08:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 11601:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 Types of wheeled fire extinguishers. 3 5 Extinguishing media, propell
9、ants and fill densities 4 6 Performance 5 7 Fire performance tests. 10 8 Construction requirements 11 9 Colour and marking 21 10 Manuals 24 Bibliography. 26 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 0
10、1/31/2009 02:08:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 11601:2008(E) iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pre
11、paring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in
12、 liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task
13、 of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention
14、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11601 was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subc
15、ommittee SC 2, Manually transportable fire extinguishers. This second edition cancels and replaces the first edition (ISO 11601:1999), which has been technically revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not
16、 for Resale, 01/31/2009 02:08:42 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 11601:2008(E) ISO 2008 All rights reserved 1 Fire fighting Wheeled fire extinguishers Performance and construction 1 Scope This International Standard specifies the p
17、rincipal requirements intended to ensure the safety, reliability and performance of wheeled fire extinguishers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc
18、es, the latest edition of the referenced document (including any amendments) applies. ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties ISO 3768, Metallic coatings Neutral salt spray test (NSS test) ISO 5923, Fire protection Fire extinguishing media Carbon
19、 dioxide ISO 7165, Fire fighting Portable fire extinguishers Performance and construction ISO 7201-1, Fire protection Fire extinguishing media Halogenated hydrocarbons Part 1: Specifications for halon 1211 and halon 1301 ISO 7202, Fire protection Fire extinguishing media Powder ISO 7203-1, Fire exti
20、nguishing media Foam concentrates Part 1: Specification for low expansion foam concentrates for top application to water-immiscible liquids ISO 7203-2, Fire extinguishing media Foam concentrates Part 2: Specification for medium and high expansion foam concentrates for top application to water-immisc
21、ible liquids ISO 14520-1, Gaseous fire-extinguishing systems Physical properties and system design Part 1: General requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 batch group of the same products made on the same production line
22、using the same lot of materials during one production shift 3.2 body metal shell of an extinguisher designed to contain the extinguishing media including any skirt Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Re
23、sale, 01/31/2009 02:08:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 11601:2008(E) 2 ISO 2008 All rights reserved 3.3 bulk range discharge range of an extinguisher when 50 % of its extinguishing medium has been expelled with the discharge valve fully open 3.4 burst
24、 pressure Pb pressure at which the extinguisher cylinder ruptures 3.5 charge of extinguisher mass or volume of extinguishing medium contained in the extinguisher expressed in volume (litres) for water- based extinguishers and in mass (kilograms) for other extinguishers 3.6 classification of fires Cl
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11601 2008
链接地址:https://www.31doc.com/p-3774209.html