《ISO-11607-1-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-11607-1-2006.pdf(32页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11607-1:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 11607-1 First edition 2006-04-15 Packaging for terminally sterilized medical devices Part 1: Requirements for materials, sterile barrier systems and packaging systems Emballages des dispositifs mdicaux striliss au stade termin
2、al Partie 1: Exigences relatives aux matriaux, aux systmes de barrire strile et aux systmes demballage ISO 11607-1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the ty
3、pefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe
4、 Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unli
5、kely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including ph
6、otocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in S
7、witzerland ii ISO 2006 All rights reserved ISO 11607-1:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 General requirements. 5 4.1 General. 5 4.2 Quality systems 5 4.3 Sampling 6 4.4 Test methods. 6
8、4.5 Documentation 6 5 Materials and preformed sterile barrier systems 7 5.1 General requirements. 7 5.2 Microbial barrier properties. 9 5.3 Compatibility with the sterilization process. 10 5.4 Compatibility with the labelling system . 10 5.5 Storage and transport 10 6 Design and development requirem
9、ents for packaging systems. 11 6.1 General. 11 6.2 Design 11 6.3 Packaging-system performance testing. 12 6.4 Stability testing. 12 7 Information to be provided 13 Annex A (informative) Guidance on medical packaging 14 Annex B (informative) Standardized test methods and procedures that may be used t
10、o demonstrate compliance with the requirements of this part of ISO 11607 17 Annex C (normative) Test method for resistance of impermeable materials to the passage of air 21 Bibliography. 22 ISO 11607-1:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organization for Standardi
11、zation) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to b
12、e represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standa
13、rds are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter
14、national Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11607-1
15、 was prepared by Technical Committee ISO/TC 198, Sterilization of health care products. ISO 11607-1 and ISO 11607-2 cancel and replace ISO 11607:2003, which has been technically revised. ISO 11607 consists of the following parts, under the general title Packaging for terminally sterilized medical de
16、vices: Part 1: Requirements for materials, sterile barrier systems and packaging systems Part 2: Validation requirements for forming, sealing and assembly processes ISO 11607-1:2006(E) ISO 2006 All rights reserved v Introduction The process of designing and developing a packaging system for terminal
17、ly sterilized medical devices is a complicated and critical endeavour. The device components and the packaging system should be combined to create a product that performs efficiently, safely, and effectively in the hands of the user. This part of ISO 11607 specifies the basic attributes required of
18、materials and pre-formed systems intended for use in packaging systems for terminally sterilized medical devices, while considering the wide range of potential materials, medical devices, packaging system designs, and sterilization methods. ISO 11607-2 describes the validation requirements for formi
19、ng, sealing and assembly processes. This part of ISO 11607 is harmonized with EN 868-1 and specifies general requirements for all packaging materials whereas EN 868 Parts 2 to 10 specify particular requirements for a range of commonly used materials. Both parts of ISO 11607 were designed to meet the
20、 Essential Requirements of the European Medical Device Directives. European standards that provide requirements for particular materials and preformed sterile barrier systems are available and known as the EN 868 series. This part of ISO 11607 has been developed as a means to show compliance with th
21、e relevant Essential Requirements of the European Directives concerning medical devices. Compliance with EN 868 Parts 2 to 10 can be used to demonstrate compliance with one or more of the requirements of this part of ISO 11607. The goal of a terminally sterilized medical device packaging system is t
22、o allow sterilization, provide physical protection, maintain sterility up to the point of use and allow aseptic presentation. The specific nature of the medical device, the intended sterilization methods(s), the intended use, expiry date, transport and storage all influence the packaging system desi
23、gn and choice of materials. One significant barrier to harmonization was terminology. The terms “package”, “final package”, “final pack”, “primary pack”, and “primary package” all have different connotations around the globe, and choosing one of these terms to be the harmonized basis for this part o
24、f ISO 11607 was considered a barrier to successful completion of this document. As a result, the term “sterile barrier system” was introduced to describe the minimum packaging required to perform the unique functions required of medical packaging: to allow sterilization, to provide an acceptable mic
25、robial barrier, and to allow for aseptic presentation. “Protective packaging” protects the sterile barrier system, and together they form the packaging system. “Preformed sterile barrier systems” would include any partially assembled sterile barrier systems such as pouches, header bags or hospital p
26、ackaging reels. An overview of sterile barrier systems can be found in Annex A. The sterile barrier system is essential to ensure the safety of terminally sterilized medical devices. Regulatory authorities recognize the critical nature of sterile barrier systems by considering them as an accessory o
27、r a component of a medical device. Preformed sterile barrier systems sold to healthcare facilities for use in internal sterilization are considered as medical devices in many parts of the world. INTERNATIONAL STANDARD ISO 11607-1:2006(E) ISO 2006 All rights reserved 1 Packaging for terminally steril
28、ized medical devices Part 1: Requirements for materials, sterile barrier systems and packaging systems 1 Scope This part of ISO 11607 specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maint
29、ain sterility of terminally sterilized medical devices until the point of use. This part of ISO 11607 is applicable to industry, to health care facilities, and wherever medical devices are placed in sterile barrier systems and sterilized. This part of ISO 11607 does not cover all requirements for st
30、erile barrier systems and packaging systems for medical devices that are manufactured aseptically. Additional requirements might also be necessary for drug/device combinations. This part of ISO 11607 does not describe a quality assurance system for control of all stages of manufacture. 2 Normative r
31、eferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5636-5:2003, Paper and board Determ
32、ination of air permeance and air resistance (medium range) Part 5: Gurley method 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 aseptic presentation introduction and transfer of a sterile product using conditions and procedures that exclude
33、microbial contamination 3.2 bioburden population of viable microorganisms on or in a product or sterile barrier system ISO/TS 11139:2006 ISO 11607-1:2006(E) 2 ISO 2006 All rights reserved 3.3 closure means used to close a sterile barrier system where no seal is formed NOTE For example, a sterile bar
34、rier system can be closed by a reusable container gasket or sequential folding to construct a tortuous path. 3.4 closure integrity characteristics of the closure, which ensures that it prevents the ingress of microorganisms under specified conditions NOTE See also 3.8. 3.5 expiry date indication of
35、the date, by which the product should be used, expressed at least as the year and month 3.6 labelling written, printed, electronic or graphic matter affixed to a medical device or its packaging system; or accompanying a medical device NOTE Labelling is related to identification, technical descriptio
36、n and use of the medical device but excludes shipping documents. 3.7 medical device any instrument, apparatus, implement, machine, appliance, implant, in vitro reagent or calibrator, software, material or other related article, intended by the manufacturer to be used, alone or in combination, for hu
37、man beings for one or more of the specific purpose(s) of diagnosis, prevention, monitoring, treatment or alleviation of disease; diagnosis, monitoring, treatment, alleviation of or compensation for an injury; investigation, replacement, modification or support of the anatomy or of a physiological pr
38、ocess, supporting or sustaining life, control of conception, disinfection of medical devices, providing information for medical purposes by means of in vitro examination of specimens derived from the human body; and which does not achieve its primary intended action in or on the human body by pharma
39、cological, immunological or metabolic means, but which may be assisted in its function by such means ISO 13485:2003 NOTE This definition from ISO 13485:2003 has been developed by the Global Harmonization Task Force (GHTF 2002). 3.8 microbial barrier property of the sterile barrier system that preven
40、ts the ingress of microorganisms under specified conditions 3.9 packaging material any material used in the fabrication or sealing of a packaging system ISO 11607-1:2006(E) ISO 2006 All rights reserved 3 3.10 packaging system combination of the sterile barrier system and protective packaging ISO/TS
41、11139:2006 3.11 preformed sterile barrier system sterile barrier system (3.22) that is supplied partially assembled for filling and final closure or sealing EXAMPLE Pouches, bags, and open reusable containers. ISO/TS 11139:2006 3.12 product result of a process ISO 9000:2000 NOTE For the purpose of s
42、terilization standards, product is tangible and can be raw material(s), intermediate(s), sub-assembly(ies) and health care product(s). ISO/TS 11139:2006 3.13 protective packaging configuration of materials designed to prevent damage to the sterile barrier system and its contents from the time of the
43、ir assembly until the point of use NOTE Adapted from ISO/TS 11139:2006. 3.14 recycled material material that has been reprocessed through a production process of waste materials for their original purpose or for other purposes 3.15 repeatability closeness of the agreement between the results of succ
44、essive measurements of the same particular quantity subject to measurement (measurand) carried out under the same conditions of measurement NOTE 1 These conditions are called repeatability conditions. NOTE 2 Repeatability conditions can include the following: the same measurement procedure; the same
45、 observer; the same measuring instrument, used under the same conditions; the same location; repetition over a short period of time. NOTE 3 Repeatability may be expressed quantitatively in terms of the dispersion characteristics of the results. NOTE 4 Adapted from International Vocabulary of Basic a
46、nd General Terms in Metrology, 1993, definition 3.6. ISO 11607-1:2006(E) 4 ISO 2006 All rights reserved 3.16 reproducibility closeness of the agreement between the results of measurements of the same particular quantity subject to measurement (measurand) carried out under changed conditions of measu
47、rement NOTE 1 A valid statement of reproducibility requires specification of the conditions changed. NOTE 2 The changed conditions can include: principle of measurement; method of measurement; observer; measuring instrument; reference standard; location; conditions of use; time. NOTE 3 Reproducibili
48、ty may be expressed quantitatively in terms of the dispersion characteristics of the results. NOTE 4 Adapted from International Vocabulary of Basic and General Terms in Metrology, 1993, definition 3.7. 3.17 reusable container rigid sterile barrier system designed to be repeatedly used 3.18 seal resu
49、lt of joining surfaces together NOTE For example, surfaces can be jointed together by use of adhesives or thermal fusion. 3.19 seal integrity characteristics of the seal, which ensures that it prevents the ingress of microorganisms under specified conditions NOTE See also 3.8. 3.20 seal strength mechanical strength of the seal 3.21 sterile free from viable microorganisms ISO/TS 11139:2006 3.22 sterile barrier system minimum package that prevents ingress of microorganisms a
链接地址:https://www.31doc.com/p-3774220.html