ISO-11252-2004.pdf
《ISO-11252-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-11252-2004.pdf(16页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11252:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 11252 Second edition 2004-11-15 Lasers and laser-related equipment Laser device Minimum requirements for documentation Lasers et quipements associs aux lasers Source laser Exigences minimales pour la documentation Copyright Inte
2、rnational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11252:2004(E) PDF disclaimer This PDF file may contain em
3、bedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility o
4、f not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameter
5、s were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise sp
6、ecified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office
7、 Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Sta
8、ndards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11252:2004(E) ISO 2004 All rights reserved iii Contents Page Forewordiv Introduction v 1 Scope1 2 Normative references .1 3 Terms and definitions.2 4 Units .2 5 Techn
9、ical data sheet.2 5.1 General.2 5.2 Beam output characteristics2 5.3 Power supply.2 5.4 Liquids and gases.3 5.5 Environmental conditions3 5.6 Mechanical interfaces.4 5.7 Safety4 6 Instruction manual4 7 Marking and labelling .4 Annex A (informative) Model of data sheet5 Bibliography .9 Copyright Inte
10、rnational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11252:2004(E) iv ISO 2004 All rights reserved Foreword IS
11、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co
12、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro
13、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me
14、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif
15、ying any or all such patent rights. ISO 11252 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9, Electro-optical systems. This second edition cancels and replaces the first edition (ISO 11252:1993), which has been technically revised. Copyright International Org
16、anization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11252:2004(E) ISO 2004 All rights reserved v Introduction This documen
17、t is a type B1 standard as defined in ISO 12100-1. The provisions of this document may be supplemented or modified by a type C standard. NOTE For machines which are covered by the scope of a type C standard and which have been designed and built according to the provisions of that standard, the prov
18、isions of that type C standard take precedence over the provisions of this type B1 standard. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networ
19、king permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 00:43:37 MDTNo reproduction or networking permitted without license from IHS -,-,- I
20、NTERNATIONAL STANDARD ISO 11252:2004(E) ISO 2004 All rights reserved 1 Lasers and laser-related equipment Laser device Minimum requirements for documentation 1 Scope This International Standard specifies the minimum documentation and information for marking and labelling, to be provided with laser d
21、evices (including laser diodes). The documentation is presented on two levels: as a technical data sheet (Clause 5) and as an instruction manual (Clause 6). This International Standard does not apply to laser products which incorporate laser devices. It also does not apply to laser devices manufactu
22、red before the date of publication of this document. Requirements on noise are not included in this standard. These requirements will be included in a subsequent amendment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated ref
23、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11145, Optics and optical instruments Lasers and laser-related equipment Vocabulary and symbols ISO 11146-1, Lasers and laser-related equipment Test
24、methods for laser beam widths, divergence angles and beam propagation ratios Part 1: Stigmatic and simple astigmatic beams ISO 11146-2, Lasers and laser-related equipment Test methods for laser beam widths, divergence angles and beam propagation ratios Part 2: General astigmatic beams ISO 11554, Opt
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11252 2004
链接地址:https://www.31doc.com/p-3774225.html