ISO-1161-AMD-1-2007.pdf
《ISO-1161-AMD-1-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-1161-AMD-1-2007.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 1161:1984/Amd.1:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 1161 Fourth edition 1984-12-15 AMENDMENT 1 2007-07-01 Series 1 freight containers Corner fittings Specification AMENDMENT 1: 45 ft containers Conteneurs de la srie 1 Pices de coin Spcifications AMENDEMENT 1: Conteneurs
2、 45 ft ISO 1161:1984/Amd.1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the
3、editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can
4、 be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat
5、 at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing fro
6、m either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved -,-,- ISO 1161:1
7、984/Amd.1:2007(E) ISO 2007 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Eac
8、h member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internation
9、al Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standard
10、s adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject o
11、f patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 1161:1984 was prepared by Technical Committee ISO/TC 104, Freight containers, Subcommittee SC 1, General purpose containers. The purpose of this amendment is to include 45 ft containe
12、rs in ISO 1161:1984. -,-,- ISO 1161:1984/Amd.1:2007(E) ISO 2007 All rights reserved 1 Series 1 freight containers Corner fittings Specification AMENDMENT 1: 45 ft containers Page 2, subclause 3.1.1 Add the following after paragraph 2: Apart from the above, 45 ft containers shall have four top interm
13、ediate fittings in the 40 ft position see Figures 1a) and 2a) and four bottom intermediate fittings in the 40 ft position see Figures 3a) and 4a). Page 2, subclause 3.2.4 Replace the first line by the following, to include “intermediate fittings”: Where a corner or intermediate fitting has an option
14、al inner side wall Page 2, Clause 4 Strength requirements Replace the first line by the following, to include “intermediate fittings”: The corner or intermediate fittings shall Page 2, 5.1 Loads Replace the first paragraph by the following, to include “intermediate fittings”: The following container
15、 design loads and criteria were used in establishing the dimensional design of corner or intermediate fittings specified in this International Standard. Replace the second paragraph by the following, to include “intermediate fittings” and “1EEE and 1 EE”: Corner and intermediate fittings for series
16、1 freight containers shall be capable of withstanding the loads calculated in accordance with the requirements of ISO 1496-1 for 1AA, 1A, 1AX, 1EEE and 1EE containers. Page 2, 5.1.1 Stacking Replace “Top corner fitting superimposed load offset ” by Top corner or intermediate fitting superimposed loa
17、d offset Replace “Bottom corner fitting (resting on flat support)” by Bottom corner or intermediate fitting (resting on flat support) Replace “Bottom corner fitting of No. 5 container offset ” by Bottom corner or intermediate fitting of No. 5 container offset -,-,- ISO 1161:1984/Amd.1:2007(E) 2 ISO
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1161 AMD 2007
链接地址:https://www.31doc.com/p-3774226.html