《ISO-11992-3-AMD-1-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-11992-3-AMD-1-2008.pdf(48页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 11992-3 Second edition 2003-04-15 AMENDMENT 1 2008-02-15 Road vehicles Interchange of digital information on electrical connections between towing and towed vehicles Part 3: Application layer for equipment other tha
2、n brakes and running gear AMENDMENT 1 Vhicules routiers change dinformations numriques sur les connexions lectriques entre vhicules tracteurs et vhicules tracts Partie 3: Couche dapplication pour les quipements autres que les quipements de freinage et les organes de roulement AMENDEMENT 1 ISO 11992-
3、3:2003/Amd.1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In do
4、wnloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in t
5、he General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the addres
6、s given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO a
7、t the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved ISO 11992-3:2003/Amd.1:2008(E)
8、 ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int
9、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic
10、al Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the
11、technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
12、ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 11992-3:2003 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. -,-,- -,-,- ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 All rights reserv
13、ed 1 Road vehicles Interchange of digital information on electrical connections between towing and towed vehicles Part 3: Application layer for equipment other than brakes and running gear AMENDMENT 1 Page iv, Foreword, 7th paragraph Replace the list of parts with the following. Part 1: Physical and
14、 data-link layers Part 2: Application layer for brakes and running gear Part 3: Application layer for equipment other than brakes and running gear Part 4: Diagnostics Page 1, Clause 2 Replace the entire list of normative references with the following new list. ISO 11898 (all parts), Road vehicles Co
15、ntroller area network (CAN) ISO 11992-1, Road vehicles Interchange of digital information on electrical connections between towing and towed vehicles Part 1: Physical and data-link layers Page 5, 6.2, 5th paragraph, 2nd sentence Delete the following sentence: “To avoid any transmission conflict duri
16、ng the dynamic address assignment phase (power-up), the PDU 2 type message shall have even PS (GE) in the predecessor transmission direction and odd PS (GE) in the successor transmission direction”. -,-,- ISO 11992-3:2003/Amd.1:2008(E) 2 ISO 2008 All rights reserved Page 7, 6.3, Figure 9 Replace the
17、 existing figure with the following new figure. Figure 9 Example of PDU 2 type message from towed vehicle #2 Page 25 Insert the following new subclauses immediately after 6.4.2.88. 6.4.2.89 Seconds Part of a parameter used to represent time. Data length: 1 byte Resolution: 0,25 s/bit, 0 s offset Dat
18、a range: 0 s to 59,75 s Type: Measured 6.4.2.90 Minutes Part of a parameter used to represent time. Data length: 1 byte Resolution: 1 min/bit, 0 min offset Data range: 0 min to 59 min Type: Measured 6.4.2.91 Hours Part of a parameter used to represent time. Data length: 1 byte Resolution: 1 h/bit, 0
19、 h offset Data range: 0 h to 23 h Type: Measured ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 All rights reserved 3 6.4.2.92 Day Part of a parameter used to represent a calendar date. NOTE 1 A value of 0 for the date is null. The values 1, 2, 3, and 4 are used to identify the first day of the month; 5, 6
20、, 7 and 8 identify the second day of the month; etc. NOTE 2 This parameter does not influence or change the hours parameter above. 6.4.2.93 Month Part of a parameter used to represent a calendar date. Data length: 1 byte Resolution: 1 month/bit, 0 offset Data range: 1 month to 12 months Type: Measur
21、ed NOTE A value of 0 for the month is null. The value 1 identifies January; 2 identifies February; etc. 6.4.2.94 Year Part of a parameter used to represent a calendar date. Data length: 1 byte Resolution: 1 year/bit, 1 985 years offset Data range: 1985 to 2 235 years Type: Measured NOTE A value of 0
22、 for the year identifies the year 1985; a value of 1 identifies 1986; etc. 6.4.2.95 Local Minute Offset Local offset in minutes from a reference time. Data length: 1 byte Resolution: 1 min/bit, 125 min offset Data range: 59 min to + 59 min Type: Measured Data length: 1 byte Resolution: 0,25 days/bit
23、, 0 day offset Data range: 0 day to 31,75 days Type: Measured -,-,- ISO 11992-3:2003/Amd.1:2008(E) 4 ISO 2008 All rights reserved 6.4.2.96 Local Hour Offset Local offset in hours from a reference time. Data length: 1 byte Resolution: 1 h/bit, -125 h offset Data range: 24 h to + 23 h Type: Measured 6
24、.4.2.97 Trailer left-hand stop light(s) command Command signal to activate the trailer left-hand stop light(s). 00 Trailer left-hand stop light(s) off 01 Trailer left-hand stop light(s) on Type: Status 6.4.2.98 Trailer right-hand stop light(s) command Command signal to activate the trailer right-han
25、d stop light(s). 00 Trailer right-hand stop light(s) off 01 Trailer right-hand stop light(s) on Type: Status 6.4.2.99 Trailer left-hand direction indicator light(s) command Command signal to activate the trailer left-hand direction indicator light(s). 00 Trailer left-hand direction indicator light(s
26、) off 01 Trailer left-hand direction indicator light(s) on Type: Status 6.4.2.100 Trailer right-hand direction indicator light(s) command Command signal to activate the trailer right-hand direction indicator light(s). 00 Trailer right-hand direction indicator light(s) off 01 Trailer right-hand direc
27、tion indicator light(s) on Type: Status -,-,- ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 All rights reserved 5 6.4.2.101 Trailer left-hand rear light(s) command Command signal to activate the trailer left-hand rear light(s). 00 Trailer left-hand rear light(s) off 01 Trailer left-hand rear light(s) on T
28、ype: Status 6.4.2.102 Trailer right-hand rear light(s) command Command signal to activate the trailer right-hand rear light(s). 00 Trailer right-hand rear light(s) off 01 Trailer right-hand rear light(s) on Type: Status 6.4.2.103 Trailer left-hand rear fog light(s) command Command signal to activate
29、 the trailer left-hand rear fog light(s). 00 Trailer left-hand rear fog light(s) off 01 Trailer left-hand rear fog light(s) on Type: Status 6.4.2.104 Trailer right-hand rear fog light(s) command Command signal to activate the trailer right-hand rear fog light(s). 00 Trailer right-hand rear fog light
30、(s) off 01 Trailer right-hand rear fog light(s) on Type: Status 6.4.2.105 Trailer left-hand reversing light(s) command Command signal to activate the trailer left-hand reversing light(s). 00 Trailer left-hand reversing light(s) off 01 Trailer left-hand reversing light(s) on Type: Status -,-,- ISO 11
31、992-3:2003/Amd.1:2008(E) 6 ISO 2008 All rights reserved 6.4.2.106 Trailer right-hand reversing light(s) command Command signal to activate the trailer right-hand reversing light(s). 00 Trailer right-hand reversing light(s) off 01 Trailer right-hand reversing light(s) on Type: Status 6.4.2.107 Traile
32、r left-hand side marker light(s) command Command signal to activate the trailer left-hand side marker light(s). 00 Trailer left-hand side marker light(s) off 01 Trailer left-hand side marker light(s) on Type: Status 6.4.2.108 Trailer right-hand side marker light(s) command Command signal to activate
33、 the trailer right-hand side marker light(s). 00 Trailer right-hand side marker light(s) off 01 Trailer right-hand side marker light(s) on Type: Status 6.4.2.109 Trailer left-hand rear width indicator light(s) command Command signal to activate the trailer left-hand rear width indicator light(s). 00
34、 Trailer left-hand rear width indicator light(s) off 01 Trailer left-hand rear width indicator light(s) on Type: Status 6.4.2.110 Trailer right-hand rear width indicator light(s) command Command signal to activate the trailer right-hand rear width indicator light(s). 00 Trailer right-hand rear width
35、 indicator light(s) off 01 Trailer right-hand rear width indicator light(s) on Type: Status -,-,- ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 All rights reserved 7 6.4.2.111 Trailer left-hand corner marker light(s) command Command signal to activate the trailer left-hand rear width indicator light(s). 0
36、0 Trailer left-hand corner marker light(s) off 01 Trailer left-hand corner marker light(s) on Type: Status 6.4.2.112 Trailer right-hand corner marker light(s) command Command signal to activate the trailer right-hand rear width indicator light(s). 00 Trailer right-hand corner marker light(s) off 01
37、Trailer right-hand corner marker light(s) on Type: Status 6.4.2.113 Trailer left-hand rear registration-plate light(s) command Command signal to activate the trailer left-hand registration-plate light(s). 00 Trailer left-hand rear registration-plate light(s) off 01 Trailer left-hand rear registratio
38、n-plate light(s) on Type: Status 6.4.2.114 Trailer right-hand rear registration-plate command light(s) Command signal to activate the trailer right-hand registration-plate light(s). 00 Trailer right-hand rear registration-plate light(s) off 01 Trailer right-hand rear registration-plate light(s) on T
39、ype: Status 6.4.2.115 Trailer rear warning light(s) command Command signal to activate the trailer rear warning light(s). 00 Trailer rear warning light(s) off 01 Trailer rear warning light(s) on Type: Status -,-,- ISO 11992-3:2003/Amd.1:2008(E) 8 ISO 2008 All rights reserved 6.4.2.116 Trailer rotati
40、ng identification light(s) command Command signal to activate the trailer rotating identification light(s). 00 Trailer rotating identification light(s) off 01 Trailer rotating identification light(s) on Type: Status 6.4.2.117 Trailer interior light(s) command Command signal to activate the trailer i
41、nterior light(s). 00 Trailer interior light(s) off 01 Trailer interior light(s) on Type: Status 6.4.2.118 Trailer work light(s) command Command signal to activate the trailer work light(s). 00 Trailer work light(s) off 01 Trailer work light(s) on Type: Status 6.4.2.119 Trailer left-hand stop light(s
42、) redundancy function This signal indicates whether a redundancy function for the trailer left-hand stop light function is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01 A redundancy function is activated Type: Measured
43、6.4.2.120 Trailer right-hand stop light(s) redundancy function This signal indicates whether a redundancy function for the trailer right-hand stop light function is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01 A redund
44、ancy function is activated Type: Measured -,-,- ISO 11992-3:2003/Amd.1:2008(E) ISO 2008 All rights reserved 9 6.4.2.121 Trailer left-hand direction indicator light(s) redundancy function This signal indicates whether a redundancy function for the trailer left-hand direction indicator light function
45、is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01 A redundancy function is activated Type: Measured 6.4.2.122 Trailer right-hand direction indicator light(s) redundancy function This signal indicates whether a redundancy
46、 function for the trailer right-hand direction indicator light function is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01 A redundancy function is activated Type: Measured 6.4.2.123 Trailer left-hand rear light(s) redund
47、ancy function This signal indicates whether a redundancy function for the trailer left-hand rear light function is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01 A redundancy function is activated Type: Measured 6.4.2.124 Trailer right-hand rear light(s) redundancy function This signal indicates whether a redundancy function for the trailer right-hand rear light function is activated. The status of the light function used for replacement is not affected. 00 A redundancy function is not activated 01
链接地址:https://www.31doc.com/p-3774246.html