ISO-13363-2004.pdf
《ISO-13363-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-13363-2004.pdf(14页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 13363 First edition 2004-02-15 Reference number ISO 13363:2004(E) ISO 2004 Rubber and plastics hoses for marine- engine wet-exhaust systems Specification Tuyaux dchappement en caoutchouc et en plastique pour moteurs de bateaux de plaisance Spcifications Copyright Internati
2、onal Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:13:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13363:2004(E) ii ISO 2004 All rights reserved PDF disclaimer T
3、his PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept t
4、herein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;
5、 the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights re
6、served. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requ
7、ester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standard
8、s 1/9972545001 Not for Resale, 04/21/2007 11:13:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13363:2004(E) ISO 2004 All rights reserved iii Contents Page 1Scope 1 2Normative references 1 3Terms and definitions 2 4Classification . 2 5Materials and construction . 2
9、6Dimensions and tolerances 3 7Physical properties 3 7.1General . 3 7.2Tensile strength and elongation at break . 3 7.3Accelerated ageing . 4 7.4Compression set (only rubber hoses) . 4 7.5Resistance to liquids (only class A hoses) . 4 7.6Loss in mass on heating (only plastics hoses) 4 8Physical tests
10、 on finished hose or tubing . 4 8.1Minimum burst pressure . 4 8.2Flexibility (for type 1 and 2 only) 4 8.3Ozone resistance (rubber hoses only) 4 8.4Ultraviolet (UV) resistance (plastics hoses only) . 4 8.5Adhesion 5 8.6Abrasion resistance 5 8.7Heat resistance 5 8.8Ageing 5 9Application of tests . 5
11、10Marking . 6 Annex A (normative) Heat-resistance test . 7 Annex B (normative) Type approval and routine tests . 8 Annex C (informative) Recommended production acceptance tests 9 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical S
12、tandards 1/9972545001 Not for Resale, 04/21/2007 11:13:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13363:2004(E) iv ISO 2004 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodi
13、es (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations
14、, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the IS
15、O/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the
16、member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13363 was prepared by Technical Committee ISO/TC 45, Rubber and rub
17、ber products, Subcommittee SC 1, Hoses (rubber and plastics). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:13:06 MDTNo reproduction or networking permitted without license
18、from IHS -,-,- INTERNATIONAL STANDARDISO 13363:2004(E) ISO 2004 All rights reserved 1 Rubber and plastics hoses for marine-engine wet-exhaust systems Specification WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to
19、address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions. 1Scope This International Standard specifies requirements for three types a
20、nd two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water). The three types are: type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement; type 2: a hardwall
21、 hose, made of oil-resistant material, with a synthetic-fabric reinforcement with a helical wire embedded in it; type 3: a hose or tube (flexible connector), made of oil-resistant material, with or without a reinforcement or cover, intended for use in short lengths in locations where the connector i
22、s protected from mechanical damage. The two classes are: class A intended for diesel engines; class B intended for petrol engines, and for diesel engines with a very high exhaust temperature. 2Normative references The following referenced documents are indispensable for the application of this docum
23、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties ISO 48, Rubber, vulcanized or thermoplast
24、ic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 176:1976, Plastics Determination of loss of plasticizers Activated carbon method ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 815, Rubber, vulcanized or thermoplastic Determinati
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13363 2004
链接地址:https://www.31doc.com/p-3774414.html