ISO-10350-1-2007.pdf
《ISO-10350-1-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-10350-1-2007.pdf(18页珍藏版)》请在三一文库上搜索。
1、 . Reference number ISO 10350-1:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 10350-1 Second edition 2007-07-15 Plastics Acquisition and presentation of comparable single-point data Part 1: Moulding materials Plastiques Acquisition et prsentation de caractristiques intrinsques comparables Partie 1: Ma
2、triaux pour moulage ISO 10350-1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing
3、 the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF fil
4、e can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secret
5、ariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writin
6、g from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved -,-,- ISO 1
7、0350-1:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 3 4 Specimen preparation and conditioning 3 5 Test requirements. 4 6 Presentation of results. 4 -,-,- ISO 10350-1:2007(E) iv ISO 2007 All rights res
8、erved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for whi
9、ch a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all m
10、atters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are cir
11、culated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held respon
12、sible for identifying any or all such patent rights. ISO 10350-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical properties. This second edition cancels and replaces the first edition (ISO 10350-1:1998), which has been technically revised. ISO 10350 consists of
13、 the following parts, under the general title Plastics Acquisition and presentation of comparable single-point data: Part 1: Moulding materials Part 2: Long-fibre-reinforced plastics ISO 10350-1:2007(E) ISO 2007 All rights reserved v Introduction ISO 10350 has been prepared because users of plastics
14、 find that available data cannot always be readily used to compare the properties of similar materials, especially when the data have been supplied by different sources. Even when the same standard tests have been used, they often allow the adoption of a wide range of alternative test conditions, an
15、d the data obtained are not necessarily comparable. The purpose of this International Standard is to identify specific methods and conditions of test to be used for the acquisition and presentation of data in order that valid comparisons between materials can be made. ISO 10350 is concerned with tes
16、ts employed to present “single-point” data on the limited range of properties commonly included in data sheets and used for the preliminary selection of materials. Such data represent the most basic approach to the specification of properties of materials, and the standard thus facilitates the first
17、 steps towards more efficient selection and use of plastics in the many applications to which they are suited. Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3)1) are concerned with the standardized acquisition and presentation of multipoint data, to demonstrate how pr
18、operties vary with important factors such as time, temperature and the presence of particular natural and chemical environments. In these standards, some additional properties are included. Their use will provide a more substantial database than one containing only single-point data, and so will ena
19、ble improved assessment of the fitness of a material for any particular application. In addition, ISO 11403-1, which deals with mechanical properties, assists predictions of the performance of components and ISO 11403-2, covering thermal and processing properties, aids predictions of melt-flow behav
20、iour during manufacturing. ISO 11403-3 is concerned with environmental influences on properties, and other parts may be prepared to cover additional properties. 1) ISO 11403-1, Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties ISO 11403-2, Plastics Acq
21、uisition and presentation of comparable multipoint data Part 2: Thermal and processing properties ISO 11403-3, Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties -,-,- -,-,- INTERNATIONAL STANDARD ISO 10350-1:2007(E) ISO 2007 All rights
22、 reserved 1 Plastics Acquisition and presentation of comparable single- point data Part 1: Moulding materials 1 Scope ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified
23、 by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers data sheets. This part of ISO 10350 applies predominantly to unreinforced and rein
24、forced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350, long-fibre-reinforced plastics are co
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10350 2007
链接地址:https://www.31doc.com/p-3774434.html