ISO-13372-2004.pdf
《ISO-13372-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-13372-2004.pdf(18页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 13372:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 13372 First edition 2004-05-15 Condition monitoring and diagnostics of machines Vocabulary Surveillance et diagnostic des machines Vocabulaire Copyright International Organization for Standardization Provided by IHS under licens
2、e with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13372:2004(E) ISO 2004 The reproduction of the terms and definitions contained in this International Standard is permitted in te
3、aching manuals, instruction booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are: that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar pu
4、blications offered for sale; and that this International Standard is referenced as the source document. With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, w
5、ithout permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All
6、rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloa
7、ding this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the Ge
8、neral Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address giv
9、en below. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13372:2004(E) ISO 2004 All rights
10、 reserved iii Contents Page Forewordiv Introduction v Scope.1 1 General terms1 2 Machine characteristics.2 3 Operation and maintenance 3 4 Faults3 5 Data collection (acquisition)4 6 Data characteristics5 7 Data (signal) processing5 8 Analysis .6 9 Diagnostics7 10 Prognostics .8 Bibliography .9 Alpha
11、betical index .10 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13372:2004(E) iv ISO 2004
12、 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a
13、subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission
14、 (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical com
15、mittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not
16、 be held responsible for identifying any or all such patent rights. ISO 13372 was prepared by Technical Committee ISO/TC 108, Mechanical vibration and shock, Subcommittee SC 5, Condition monitoring and diagnostics of machines. Copyright International Organization for Standardization Provided by IHS
17、under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13372:2004(E) ISO 2004 All rights reserved v Introduction This International Standard defines terms relating only to
18、 condition monitoring and diagnostics of machines. It does not include terms that are defined elsewhere, nor those specific to only one area of the field. It is considered a living document and will be amended or updated as additional terms arise. Copyright International Organization for Standardiza
19、tion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Lic
20、ensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:41:44 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 13372:2004(E) ISO 2004 All rights reserved 1 Condition monitoring and diagnostics of machines Vocabulary Scope This Int
21、ernational Standard specifies definitions of terms used in condition monitoring and diagnostics of machines. It is intended to provide users and manufacturers of condition monitoring and diagnostics systems with a common vocabulary. 1 General terms 1.1 analysis careful scrutiny of constituent parts
22、of a system (1.17) in order to thoroughly understand the whole 1.2 breakdown maintenance maintenance performed after a machine (1.10) has failed 1.3 catastrophic failure sudden, unexpected failure (1.7) of a machine (1.10) resulting in considerable damage to the machine and/or associated machines or
23、 components 1.4 condition-based maintenance maintenance performed as governed by condition monitoring programmes 1.5 condition monitoring detection and collection of information and data that indicate the state of a machine (1.10) NOTE The machine state deteriorates if faults (1.8) or failures (1.7)
24、 occur. 1.6 diagnostics examination of symptoms (9.5) and syndromes (4.9) to determine the nature of faults (1.8) or failures (1.7) (kind, situation, extent) 1.7 failure termination of the ability of an item to perform a required function (1.9) NOTE Failure is an event as distinguished from fault (1
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13372 2004
链接地址:https://www.31doc.com/p-3774456.html