ISO-13433-2006.pdf
《ISO-13433-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-13433-2006.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 13433:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 13433 First edition 2006-08-01 Geosynthetics Dynamic perforation test (cone drop test) Gosynthtiques Essai de perforation dynamique (essai par chute dun cne) ISO 13433:2006(E) PDF disclaimer This PDF file may contain embedded ty
2、pefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not inf
3、ringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were op
4、timized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified,
5、no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case pos
6、tale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved -,-,- ISO 13433:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Terms and
7、 definitions. 1 4 Principle. 1 5 Apparatus 2 6 Specimens. 5 6.1 Sampling 5 6.2 Number and dimension of specimens 5 7 Conditioning 6 8 Procedure 6 9 Calculation. 6 10 Test report . 6 -,-,- ISO 13433:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organization for Standardizati
8、on) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be re
9、presented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards
10、are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internati
11、onal Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13433 was p
12、repared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 189, Geosynthetics in collaboration with Technical Committee ISO/TC 221, Geosynthetics, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). -,-,- INTERNATIONAL STANDAR
13、D ISO 13433:2006(E) ISO 2006 All rights reserved 1 Geosynthetics Dynamic perforation test (cone drop test) 1 Scope This International Standard specifies a method to determine the resistance of geosynthetics to penetration by a steel cone dropped from a fixed height. The degree of penetration is an i
14、ndication of the behaviour of the geosynthetic when sharp stones are dropped on its surface. The method is generally applicable to geosynthetics. However, the validity of this test for some types of products should be considered carefully, as the test principle may not be applicable. 2 Normative ref
15、erences The following referenced documents are indispensable for the application of this document. For dated references, only the cited edition applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 554, Standard atmospheres for conditi
16、oning and/or testing Specifications ISO 9862, Geosynthetics Sampling and preparation of test specimens ISO 10320, Geotextiles and geotextile-related products Identification on site 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 hole size dia
17、meter of the hole made by the cone in penetrating the specimen NOTE The hole size is measured in millimetres. 4 Principle The specimen is clamped horizontally between two steel rings. A stainless steel cone is dropped, point first, from a distance of 500 mm onto the centre of the specimen. The degre
18、e of penetration is measured by inserting a narrow-angle graduated cone into the hole. ISO 13433:2006(E) 2 ISO 2006 All rights reserved 5 Apparatus 5.1 Clamping system. The clamping system shall prevent slippage or cutting of the specimen during the test. An example of the clamping system and the gu
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13433 2006
链接地址:https://www.31doc.com/p-3774525.html