ISO-13709-2003.pdf
《ISO-13709-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-13709-2003.pdf(192页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 13709:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 13709 First edition 2003-07-01 Centrifugal pumps for petroleum, petrochemical and natural gas industries Pompes centrifuges pour les industries du ptrole, de la ptrochimie et du gaz naturel Copyright International Organization f
2、or Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 01:14:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13709:2003(E) PDF disclaimer This PDF file may contain embedded typefaces.
3、In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing A
4、dobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized f
5、or printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part o
6、f this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 C
7、H-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing,
8、 Bernie Not for Resale, 04/03/2007 01:14:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13709:2003(E) ISO 2003 All rights reserved iii Contents Page Foreword.v Introduction .vi 1 Scope1 2 Normative references .1 3 Terms and definitions.4 4 Classification and designa
9、tion9 4.1 General.9 4.2 Pump designations.10 4.3 Units and governing requirements .16 5 Basic design16 5.1 General.16 5.2 Pump types20 5.3 Pressure casings 21 5.4 Nozzles and pressure casing connections 23 5.5 External nozzle forces and moments25 5.6 Rotors.31 5.7 Wear rings and running clearances33
10、 5.8 Mechanical shaft seals.34 5.9 Dynamics .37 5.10 Bearings and bearing housings 46 5.11 Lubrication.49 5.12 Materials.50 5.13 Nameplates and rotation arrows .55 6 Accessories.55 6.1 Drivers55 6.2 Couplings and guards58 6.3 Baseplates .59 6.4 Instrumentation.62 6.5 Piping and appurtenances.62 6.6
11、Special tools63 7 Inspection, testing, and preparation for shipment64 7.1 General.64 7.2 Inspection 64 7.3 Testing66 7.4 Preparation for shipment .70 8 Specific pump types .71 8.1 Single-stage overhung pumps.71 8.2 Between-bearings pumps (types BB1 through BB5) 73 8.3 Vertically suspended pumps (typ
12、es VS1 through VS7)78 9 Vendors data.84 9.1 General.84 9.2 Proposals.85 9.3 Contract data.88 Annex A (informative) Specific speed and suction-specific speed.90 Annex B (normative) Cooling water and lubrication system schematics.91 Annex C (normative) Hydraulic power recovery turbines 102 Copyright I
13、nternational Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 01:14:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13709:2003(E) iv ISO 2003 All rights reserved An
14、nex D (normative) Standard baseplates 106 Annex E (informative) Inspectors checklist 108 Annex F (normative) Criteria for piping design.110 Annex G (informative) Materials class selection guidance 124 Annex H (normative) Materials and material specifications for pump parts126 Annex I (normative) Lat
15、eral analysis136 Annex J (normative) Determination of residual unbalance142 Annex K (normative) Seal chamber runout illustrations148 Annex L (informative) Vendor drawing and data requirements.149 Annex M (informative) Test data summary.158 Annex N (informative) Pump datasheets162 Bibliography181 Cop
16、yright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 01:14:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13709:2003(E) ISO 2003 All rights reserv
17、ed v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for whic
18、h a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all ma
19、tters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circ
20、ulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held respons
21、ible for identifying any or all such patent rights. ISO 13709 was prepared by Technical Committee ISO/TC 115, Pumps, Subcommittee SC 3, Installation and special application, in collaboration with Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical
22、 and natural gas industries, SC 6, Processing equipment and systems. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 01:14:34 MDTNo reproduction or networking permitted wit
23、hout license from IHS -,-,- ISO 13709:2003(E) vi ISO 2003 All rights reserved Introduction This International Standard was developed from API Standard 610, 8th edition, 1995, with the intent that the 9th edition of API 610 will be the same as this International Standard. Users of this International
24、Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting alternative equipment or engineering solutions for the individual application. Thi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13709 2003
链接地址:https://www.31doc.com/p-3774574.html