《ISO-1361-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-1361-1997.pdf(5页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 1361 Fourth edition 1997-l 2-l 5 Light-gauge metal containers - Round open-top cans - Internal diameters RBcipients m6talliques Ikgers - Boites rondes serties - Diam - nominal necked-in diameters are included which, associated with the internal body diameters, allow the st
2、acking of three-piece cans ; - the following diameters, which were considered acceptable until the end of 1987, are deleted : 56; 57; 61; 70; 71; 72; 93; 100; 109; 113; 126; 135; 138; 154 ; - a new list of diameters which are acceptable for a five-year period has been drawn up. 0 IS0 1997 All rights
3、 reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale
4、56 l CH-1211 Gen a=400net; p=iso; o=isocs; s=central Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:55:31 MDTNo reproduction or networking permitted
5、 without license from IHS -,-,- INTERNATIONAL STANDARD IS0 IS0 1361:1997(E) Light-gauge metal containers - Round open-top cans - Internal diameters 1 Scope This International Standard establishes a list of recommended diameters for round two-piece and three- piece cans in tinplate or aluminium seame
6、d after filling and defined by their nominal gross lidded capacity. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of the publication, the editions indicated were valid. All st
7、andards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. I
8、S0 90-l: 1997, Light gauge metal containers - Definitions and determination of dimensions and capacities - Part 7: Open-top cans. IS0 10653:1993, Light-gauge metal containers - Round open-top cans - Cans defined by their nominal gross lidded capacity. 3 Recommended diameters Table 1 gives the range
9、: - of the nominal diameters of two- and three-piece cans ; - of the corresponding actual internal body diameters for three-piece cans ; - of the nominal necked-in diameters associated with the internal body diameters to allow stacking of three-piece cans ; - of the opening diameters for two-piece c
10、ans. All specified can dimensions given are in accordance with the provisions of IS0 90-I. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:55:31 MDTNo reproduction or networ
11、king permitted without license from IHS -,-,- IS0 1361:1997(E) Table 1 0 IS0 Three-piece cans Two-piece cans Nominal Actual Tolerance2) Necked-in diameter 3) internal diameter Opening Tolerance2) 4, D body + Nominal diameter diameter diameter DN6) + mm mm mm mm mm mm 52 52,27 0,io 49 52,40 5, ) 0,20
12、 63 62,41 0,12 60 63,00 II 65 65.28 0,12 62 65.45 II 73 72,80 0,15 70 72,99 II 83 83,33 0,155 80 83,55 ) 0,30 99 98,99 0,16 96 99,25 40 105 105,16 0,18 102 105,43 II 127 126,45 0,22 123 126,78 II 153 153,35 0,22 149 l53,77 0,40 189 188,90 0,22 4, 230 229,67 0,22 225 230,09 II n these cases, for step
13、-sided cans, the internal body diameter may conform to the value in the “Opening diameter” column. rhese tolerances define the limits of acceptable deviations resulting from variations in can design. In some cases, the method of rounding the internal body diameter or the opening diameter to determin
14、e the nominal diameter is in accordance with the method described in IS0 90-l. rolerances given in this column take into account cans made of steel plate or aluminium. Some existing two-piece cans may not conform. The nominal necked-in diameter the nominal necked-in diameter DN shown shall not be us
15、ed as the nominal diameter in connection with IS0 10653. 4 Provisional additional diameters The following currently used diameters are acceptable for a five-year period. After five years, these diameters will be reconsidered and either deleted or incorporated into this International Standard: 55; 60
16、; 71,5; 74; 86; 155; 163; 171 As this list is only valid for a limited period, the internal body diameters and opening diameters are not specified. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for R
17、esale, 04/28/2007 04:55:31 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 1361:1997(E) 0 IS0 ICS 55.120 Descriptors: packaging, metal packaging, food packaging, containers, cans, dimensions, diameters, dimensional tolerances. Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:55:31 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3774579.html