ISO-13534-2000.pdf
《ISO-13534-2000.pdf》由会员分享,可在线阅读,更多相关《ISO-13534-2000.pdf(20页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 13534:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 13534 First edition 2000-12-01 Petroleum and natural gas industries Drilling and production equipment Inspection, maintenance, repair and remanufacture of hoisting equipment Industries du ptrole et du gaz naturel quipement de for
2、age et de production Vrification, maintenance, rparation et fabrication partir de matriaux recycls du matriel de levage Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 M
3、DTNo reproduction or networking permitted without license from IHS -,-,- ISO 13534:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are l
4、icensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details o
5、f the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relati
6、ng to it is found, please inform the Central Secretariat at the address given below. ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, withou
7、t permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights
8、reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13534:2000(E) ISO 2000 All rights
9、reservediii ContentsPage Foreword.iv Introduction.v 1Scope 1 2Normative reference2 3Terms, definitions and abbreviated terms 2 3.1Terms and definitions .2 3.2Abbreviated terms .3 4General principles3 4.1Procedures.3 4.2Personnel qualification .4 5Inspection and maintenance 4 5.1General4 5.2Maintenan
10、ce.5 5.3Inspection.5 6Repair9 6.1Procedures.9 6.2Bearings9 6.3Replacement parts.9 7Remanufacture.9 7.1Procedures.9 7.2Verification .10 8Load testing10 8.1General10 8.2Performance load test.10 8.3Proof load test10 9Documentation and records.10 9.1General10 9.2User/owner equipment file10 9.3Activity r
11、ecords11 Bibliography12 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13534:2000(E) iv IS
12、O 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested
13、 in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Comm
14、ission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as
15、an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such pate
16、nt rights. International Standard ISO 13534 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum and natural gas industries, Subcommittee SC 4, Drilling and production equipment. Copyright International Organization for Standardization Provided by
17、 IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13534:2000(E) ISO 2000 All rights reservedv Introduction This International Standard is based on API RP 8B, 6th
18、edition, December 1997 1. Users of this International Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit the user from utilizing alternative equipment, methods or engineering solutions for
19、individual applications. This may be particularly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard and provide details. Copyright International Organization for Standardization P
20、rovided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=
21、NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 22:09:46 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 13534:2000(E) ISO 2000 All rights reserved1 Petroleum and natural gas industries Drilling and production equipment Inspection,
22、 maintenance, repair and remanufacture of hoisting equipment 1Scope This International Standard gives guidelines and establishes requirements for inspection, maintenance, repair and remanufacture of items of hoisting equipment used in drilling and production operations, in order to maintain the serv
23、iceability of this equipment. Items of drilling and production hoisting equipment covered by this International Standard are: ?crown-block sheaves and bearings; ?travelling blocks and hook blocks; ?block-to-hook adapters; ?connectors and link adapters; ?drilling hooks; ?tubing hooks and sucker-rod h
24、ooks; ?elevator links; ?casing elevators, tubing elevators, drill-pipe elevators and drill-collar elevators; ?sucker-rod elevators; ?rotary swivel-bail adapters; ?rotary swivels; ?power swivels; ?power subs; ?spiders, if capable of being used as elevators; ?dead-line tie-down/wireline anchors; ?dril
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13534 2000
链接地址:https://www.31doc.com/p-3774638.html