ISO-14116-2008.pdf
《ISO-14116-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-14116-2008.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 14116:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 14116 First edition 2008-04-15 Protective clothing Protection against heat and flame Limited flame spread materials, material assemblies and clothing Vtements de protection Protection contre la chaleur et la flamme Matriaux, ass
2、emblages de matriaux et vtements propagation de flamme limite -,-,- ISO 14116:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licens
3、ed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the
4、 software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to
5、 it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopyi
6、ng and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerla
7、nd ii ISO 2008 All rights reserved ISO 14116:2008(E) ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out th
8、rough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collab
9、orates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Stan
10、dards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of
11、 this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14116 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and li
12、fejackets, in collaboration with Technical Committee ISO/TC 94, Personal safety Protective clothing and equipment, Subcommittee SC 13, Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). ISO 14116 supersedes EN 533:1997, which has be
13、en technically revised to include: a) the testing of clothing for limited contact with flames specified; b) the requirements for the design of clothing specified; c) the requirements for mechanical performance of clothing specified; d) the ageing due to washing specified (maximum number of cleaning
14、procedures as indicated by the manufacturer); e) the marking requirements modified; f) the information to be supplied by the manufacturer modified. -,-,- -,-,- INTERNATIONAL STANDARD ISO 14116:2008(E) ISO 2008 All rights reserved 1 Protective clothing Protection against heat and flame Limited flame
15、spread materials, material assemblies and clothing 1 Scope This International Standard specifies the performance requirements for the limited flame spread properties of materials, material assemblies and protective clothing in order to reduce the possibility of the clothing burning and thereby itsel
16、f constituting a hazard. Additional requirements for clothing are also specified. Protective clothing complying with this International Standard is intended to protect workers against occasional and brief contact with small igniting flames, in circumstances where there is no significant heat hazard
17、and without the presence of another type of heat. When protection against heat hazards is necessary in addition to protection against limited spread flammability, then standards, such as ISO 11612, are more appropriate. A classification system is given for materials, material assemblies and garments
18、 which are tested according to ISO 15025:2000, Procedure A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (i
19、ncluding any amendments) applies. ISO 13934-1:1999, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elongation at maximum force using the strip method ISO 13935-2:1999, Textiles Seam tensile properties of fabrics and made-up textile articles Part 2: Determination of
20、 maximum force to seam rupture using the grab method ISO 13937-2:2000, Textiles Tear properties of fabrics Part 2: Determination of tear force of trouser- shaped test specimens (Single tear method) ISO 15025:2000, Protective clothing Protection against heat and flame Method of test for limited flame
21、 spread EN 340:2003, Protective clothing General requirements -,-,- ISO 14116:2008(E) 2 ISO 2008 All rights reserved 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 ageing changing of the product performance over time during use or storage NO
22、TE Ageing is caused by a combination of several factors, such as: cleaning, maintenance or disinfecting process; exposure to visible and/or ultra-violet radiation; exposure to high or low temperatures or to changing temperatures; exposure to chemicals including humidity; exposure to biological agent
23、s such as bacteria, fungi, insects or other pests; exposure to mechanical action such as abrasion, flexing, pressure and strain; exposure to contaminants such as dirt, oil, splashes of molten metal, etc.; exposure to wear and tear. ISO 11611:2007, definition 3.1 3.2 assembly two or more separate lay
24、ers of the same or different materials, or several garments to be worn together 3.3 cleaning process by which a PPE is made serviceable and/or hygienically wearable again by removing any dirt or contamination NOTE A cleaning cycle is typically a washing plus drying or a dry cleaning treatment follow
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 14116 2008
链接地址:https://www.31doc.com/p-3774655.html