ISO-1436-2-2005.pdf
《ISO-1436-2-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-1436-2-2005.pdf(18页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 1436-2:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 1436-2 First edition 2005-10-01 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 2: Water-based fluid applications Tuyaux et flexibles en caoutchouc Types hydrauliques avec armature de f
2、ils mtalliques tresss Spcifications Partie 2: Applications pour fluide base deau Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:27:22 MDTNo reproduction or networking permitt
3、ed without license from IHS -,-,- ISO 1436-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the comput
4、er performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create
5、 this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the C
6、entral Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IS
7、O at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Org
8、anization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:27:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1436-2:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword
9、 iv 1 Scope . 1 2 Normative references. 1 3 Classification. 2 4 Materials and construction 2 4.1 Hoses . 2 4.2 Hose assemblies. 2 5 Dimensions 2 5.1 Hose diameters, cover thickness and hose concentricity . 2 5.2 Length 4 6 Performance requirements 4 6.1 General. 4 6.2 Hydrostatic requirements 4 6.3
10、Minimum bend radius. 5 6.4 Resistance to impulse 6 6.5 Leakage of hose assemblies . 6 6.6 Cold flexibility . 6 6.7 Adhesion between components 6 6.8 Vacuum resistance. 6 6.9 Abrasion resistance 7 6.10 Fluid resistance. 7 6.11 Ozone resistance 7 7 Marking 8 7.1 Hoses . 8 7.2 Hose assemblies. 8 Annex
11、A (normative) Type and routine testing of production hoses . 9 Annex B (informative) Production acceptance testing. 10 Annex C (informative) Recommendations for lengths of supplied hoses and tolerances on lengths of hose assemblies. 11 Bibliography. 12 Copyright International Organization for Standa
12、rdization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:27:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1436-2:2005(E) iv ISO 2005 All rights reserved Foreword ISO (the International Organizatio
13、n for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has
14、 the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Inter
15、national Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publicat
16、ion as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent righ
17、ts. ISO 1436-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). Together with Part 1 (see below), this part of ISO 1436 cancels and replaces ISO 1436:1991, which has been technically revised. ISO 1436 consists of the following
18、 parts, under the general title Rubber hoses and hose assemblies Wire- braid-reinforced hydraulic types Specification: Part 1: Oil-based fluid applications Part 2: Water-based fluid applications Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=
19、NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 03:27:22 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 1436-2:2005(E) ISO 2005 All rights reserved 1 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specific
20、ation Part 2: Water-based fluid applications 1 Scope This part of ISO 1436 specifies requirements for six types of wire-braid-reinforced hose and hose assembly of nominal size from 5 to 51. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 a
21、t temperatures ranging from 40 C to +60 C. This part of ISO 1436 does not include requirements for end fittings. It is limited to requirements for the performance of hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the com
22、patibility of the hose with the fluid to be used. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a
23、ny amendments) applies. ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing ISO 1436-1, Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications ISO 1817, Rubber, vulcanized Determination of the effect of liquid
24、s ISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of dimensions ISO 4672:1997, Rubber and plastics hoses Sub-ambient temperature flexibility tests ISO 6605, Hydraulic fluid power Hoses and hose assemblies Test methods ISO 6803, Rubber or plastics hoses and hose assembl
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1436 2005
链接地址:https://www.31doc.com/p-3774662.html