ISO-13501-2005.pdf
《ISO-13501-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-13501-2005.pdf(58页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 13501:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 13501 First edition 2005-12-01 Petroleum and natural gas industries Drilling fluids Processing systems evaluation Industries du ptrole et du gaz naturel Fluides de forage valuation des systmes de traitement Copyright Internation
2、al Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/06/2007 23:19:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13501:2005(E) PDF disclaimer This PDF file may contain embedded
3、typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not i
4、nfringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were
5、optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified
6、, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case p
7、ostale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards
8、1/9972545001 Not for Resale, 04/06/2007 23:19:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13501:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms, definitions, symbols and abbreviated t
9、erms. 1 4 Requirements 12 5 Drilled solids removal System performance. 12 6 Rigsite evaluation of drilled-solids management equipment. 17 7 Practical operational guidelines 21 8 Conductance of shale-shaker screens. 30 9 Shale-shaker screen designation 35 10 Non-blanked area of shale-shaker screen pa
10、nel. 43 11 Shale-shaker screen labelling. 45 Annex A (informative) Derivation of capture equation. 49 Bibliography. 51 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/06/2007 23:19:04 MD
11、TNo reproduction or networking permitted without license from IHS -,-,- ISO 13501:2005(E) iv ISO 2005 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International
12、Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, al
13、so take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committ
14、ees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the poss
15、ibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13501 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical
16、and natural gas industries, Subcommittee SC 3, Drilling and completion fluids, and well cements. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/06/2007 23:19:04 MDTNo reproduction or ne
17、tworking permitted without license from IHS -,-,- ISO 13501:2005(E) ISO 2005 All rights reserved v Introduction This International Standard covers equipment which is commonly used in petroleum and natural gas drilling fluids processing. This equipment can be purchased or rented from multiple sources
18、, and is available worldwide. No single-source or limited-source equipment is included, either by inference or reference. International Standards are published to facilitate communications between purchasers and manufacturers, or provide interchangeability between similar equipment and materials pur
19、chased from different manufacturers and/or at different times, and to provide an adequate level of safety when the equipment or materials are utilized in the manner and for the purposes intended. This International Standard provides minimum requirements and is not intended to inhibit anyone from pur
20、chasing or using equipment made to other standards. This International Standard is subject to periodic review and can be revised or withdrawn at such time as deemed appropriate. The purpose of this International Standard is to provide a method of assessing the performance of solids control equipment
21、 systems in the field. It includes procedures for evaluation of shale shakers, centrifugal pumps, degassers, hydrocyclones, mud cleaners and centrifuges, as well as an entire system evaluation. Shale-shaker screenLabelling and separation potential of shale-shaker screens have been addressed as part
22、of this International Standard. This International Standard is based on API RP 13C, third edition, December 2004 (for drilling fluid processing equipment) and shale-shaker screen API RP 13E, third edition, May 1, 1993 (for shale-shaker screens). ISO publications may be used by anyone desiring to do
23、so. Every effort has been made to assure the accuracy and reliability of the data contained in them; however, no representation, warrant or guarantee in connection with this publication is made by ISO. ISO hereby expressly disclaims any liability, or responsibility for loss or damage resulting from
24、use of this International Standard or for the violation of any federal, state or municipal regulation with which this publication may conflict. Standards are published to facilitate the broad availability of proven, sound engineering and operating practices. Users of this International Standard shou
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13501 2005
链接地址:https://www.31doc.com/p-3774669.html