《ISO-14278-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-14278-2002.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 14278:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 14278 First edition 2002-06-15 Aerospace Gauges, for internal offset cruciform ribbed or unribbed drives Metric series Aronautique et espace Calibres de contrle, pour empreintes cruciformes dportes avec ou sans saillies antidrap
2、antes Srie mtrique Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) PDF discla
3、imer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties ac
4、cept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the
5、 file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All rig
6、hts reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of th
7、e requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with IS
8、O Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) ISO 2002 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federatio
9、n of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
10、 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wi
11、th the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appro
12、val by at least 75 % of the member bodies casting a vote. ISO 14278 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4, Aerospace fastener systems. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA
13、 Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) iv ISO 2002 All rights reserved Introduction The International Organization for Standardization (ISO) draws attention to the fact that it
14、is claimed that compliance with this International Standard may involve the use of a patent concerning gauges specified in this International Standard. Patent rights are held by the Phillips Screw Company worldwide. ISO takes no position concerning the evidence, validity and scope of this patent rig
15、ht. The holder of this patent right has assured the ISO that he is willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with the ISO. Informatio
16、n may be obtained from: Phillips Screw Company 508 Edgewater Drive Wakefield, MA 01880 USA Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights other than those identified above. ISO shall not be held responsible for ident
17、ifying any or all such patent rights. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATI
18、ONAL STANDARD ISO 14278:2002(E) ISO 2002 All rights reserved 1 Aerospace Gauges, for internal offset cruciform ribbed or unribbed drives Metric series 1 Scope This International Standard specifies the dimensions of metric gauges which check internal offset cruciform drives, ribbed or unribbed, used
19、in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. The internal offset cruciform drives, ribbed drives and unribbed, respectively are defined in ISO 14275 and ISO 14276. 2 Configuration and dimensions See Figures 1, 2 and 3 and Tables 1 and 2. Dimensions and tolerances are exp
20、ressed in millimetres. The presentation of surface-profile, perpendicularity, location and run-out tolerances conforms to ISO 1101. 3 Designation The GO and NOT GO gauge designation shall be as follows: The component part designation shall be as follows: The drive penetration gauge assembly (see Fig
21、ure 3) shall be identified by the gauge body designation. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from
22、 IHS -,-,- ISO 14278:2002(E) 2 ISO 2002 All rights reserved Gauges made from heat-treatable corrosion-resisting steel and heat-treated to a hardness of 58 HRC to 62 HRC. Figure 1 Configuration Drive GO (A) and NOT GO (C) gauges Copyright International Organization for Standardization Provided by IHS
23、 under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) ISO 2002 All rights reserved 3 Table 1 Dimensions Drive GO and NOT GO gauges B F G H R S T Y Drive GO
24、 and NOT GO gauge code Gauge type A ref. max. 0 0,003 0,03 0,25 max. 0 0,05 0,03 0 + 0,05 0 + Drive GO and NOT GO gauge code inches a R1,6A GO 0,81 0,406 0,96 6,35 0A R1,6C NOT GO 0,917 0,46 1,65 7,92 0C R2A GO 0,81 0,406 1,14 6,35 1A R2C NOT GO 0,917 0,46 1,96 7,92 1C R2,5A GO 0,912 0,457 1,52 6,35
25、 3A R2,5C NOT GO 1,069 0,1 0,536 2,64 9,52 0,13 3C R3A GO 1,013 0,508 1,73 6,35 4A R3C NOT GO 1,171 0,587 3,05 9,52 0,18 0,74 1,12 4C R3,5A GO 1,318 0,66 2,11 6,35 6A R3,5C NOT GO 1,476 0,15 0,739 3,4 11,12 0,86 1,37 6C R4A GO 1,572 0,787 2,46 6,35 8A R4C NOT GO 1,73 0,866 4,04 11,12 0,38 1,07 1,57
26、8C R5A GO 1,826 0,914 2,84 6,35 10A R5C NOT GO 1,984 0,23 0,993 4,34 1,27 1,78 10C R6A GO 2,436 1,219 3,76 11,12 1/4A R6C NOT GO 2,593 1,298 5,72 15,88 0,56 1,75 2,26 1/4C R8A GO 3,096 1,549 4,72 11,12 5/16A R8C NOT GO 3,254 1,628 7,16 15,88 2,31 2,95 5/16C R10A GO 3,706 1,854 5,64 11,12 3/8A R10C N
27、OT GO 3,863 0,36 1,933 8,58 0,76 2,84 0,1 3,48 3/8C R12A GO 4,976 2,489 7,47 15,88 1/2A R12C NOT GO 5,184 2,593 11,43 19,05 3,89 0,11 4,52 1/2C R14A GO 5,636 2,819 8,38 17,48 9/16A R14C NOT GO 5,844 2,924 12,85 19,05 4,34 5,1 9/16C R16A GO 6,246 3,124 9,32 17,48 5/8A R16C NOT GO 6,454 3,228 14,27 19
28、,05 4,85 0,14 5,61 5/8C R18A GO 7,516 3,759 11,12 25,4 3/4A R18C NOT GO 7,724 0,51 3,863 17,14 31,75 1,02 5,92 0,18 6,68 3/4C a For information and comparison purposes only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standa
29、rds 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) 4 ISO 2002 All rights reserved Break sharp edges 0,1 to 0,4. a) Gauge body b b) Gauge holder b Copyright International Organization for Standardization Pro
30、vided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) ISO 2002 All rights reserved 5 c) Gauge point assembly b d) Gauge collar b Key 1 Gauge po
31、int 2 Gauge holder a Shape at manufacturers option. b The body, holder and collar, but not gauge point, shall be made from corrosion-resistant steel 440C and heat-treated to a hardness of 30 HRC to 35 HRC. c Configuration of gauge point in conformity with Figure 1, drive gauge type GO (A) machined t
32、o dimension F. d Secure the gauge point to the holder using adhesive Eastman 910 or equivalent. (Eastman 910 is the trade name of a suitable product available commercially. This information is given for the convenience of users of this International Standard and does not constitute an endorsement by
33、 ISO of this product.) Figure 2 Configuration Drive penetration gauge component parts Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking pe
34、rmitted without license from IHS -,-,- ISO 14278:2002(E) 6 ISO 2002 All rights reserved Table 2 Dimensions Drive penetration gauge component parts A B C E F G H J K M N P Q S T U Component part code 0 0,013 0,41 0,41 0,03 0,13 0,05 0 + 0,41 0 + 0,41 0,03 0 + 0,41 0,13 0 + 0,05 0 + 0,41 0,41 0 0,013
35、0,41 Component part code inches a R1,6 1,85 0 R2 0,86 2,21 0,84 1 R2,5 0,96 2,95 0,94 3 R3 1,07 3,33 1,04 4 R3,5 1,37 4,06 1,35 6 R4 1,62 4,83 1,60 8 R5 9,512 21,44 12,70 1,88 12,95 5,56 0,79 22,22 9,52 3,18 47,02 1,85 4,78 10 R6 2,49 7,26 2,46 1/4 R8 3,15 9,07 3,12 5/16 R10 3,76 10,85 6,35 3,73 3/8
36、 R12 5,03 14,43 5,00 1/2 R14 5,69 16,21 5,66 9/16 R16 19,037 18,26 6,30 20,32 17,98 1,57 31,75 19,05 6,27 3,18 19,0371,57 5/8 R18 28,562 15,88 9,52 7,57 21,59 21,56 2,77 50,80 28,58 3,18 44,45 7,54 7,92 6,35 28,5623,18 3/4 a For information and comparison purposes only. Copyright International Organ
37、ization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) ISO 2002 All rights reserved 7 a) Components b) Zero posit
38、ion determination Key 1 Dial indicator AMES Model 214-25J or equivalent Graduations: 0,01 Range: 25 Continuous dial reading counter-clockwise with revolution counter 2 Gauge collar 3 Spring Material: corrosion-resisting steel Size: diameter 7,62 25,4 long Wire diameter: 0,66 Ends: squared and ground
39、 4 Gauge point assembly 5 Setscrew M6-4g6g 8 long, hexagon socket, plain cup point 6 Gauge body 7 Gauge body identification marking Figure 3 Configuration Drive penetration gauge assembly Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Te
40、chnical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) 8 ISO 2002 All rights reserved Bibliography 1 ISO 1101:1), Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of for
41、m, orientation, location and run-out 2 ISO 14275:2002, Aerospace Drives, internal, offset cruciform, ribbed Metric series 3 ISO 14276:2002, Aerospace Drives, internal, offset cruciform Metric series 1) To be published. (Revision of ISO 1101:1983) Copyright International Organization for Standardizat
42、ion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Lice
43、nsee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14278:2002(E) ICS 49.030.20 Price based on 8 pages ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:19:34 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3774680.html