ISO-13535-2000.pdf
《ISO-13535-2000.pdf》由会员分享,可在线阅读,更多相关《ISO-13535-2000.pdf(54页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 13535:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 13535 First edition 2000-12-15 Petroleum and natural gas industries Drilling and production equipment Hoisting equipment Industries du ptrole et du gaz naturel quipements de forage et de production quipement de levage ISO 13535:2
2、000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
3、 file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Inf
4、o relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
5、 ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in
6、the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reserved ISO 13535:2000(E) ISO 2000 All rights reservediii ContentsPage Forewordv In
7、troductionvi 1Scope 1 2Normative references2 3Terms, definitions and abbreviated terms 3 3.1Terms and definitions .3 3.2Abbreviated terms .5 4Design.5 4.1General5 4.2Design conditions5 4.3Strength analysis.5 4.4Size class7 4.5Contact surface radii.7 4.6Rating7 4.7Design safety factor 7 4.8Shear stre
8、ngth8 4.9Specific equipment8 4.10Design documentation8 5Design verification test .8 5.1General8 5.2Sampling of test units .8 5.3Test procedures.8 5.4Determination of load rating.9 5.5Alternative design verification test procedure and rating.9 5.6Design verification test apparatus.10 5.7Design change
9、s .10 5.8Records.10 6Materials requirements .10 6.1General10 6.2Written specifications .10 6.3Mechanical properties.11 6.4Material qualification.11 6.5Manufacture12 6.6Chemical composition 12 7Welding requirements.15 7.1General15 7.2Welding qualifications.15 7.3Written documentation15 7.4Control of
10、consumables15 7.5Weld properties15 7.6Post-weld heat-treatment16 7.7Fabrication welds.16 7.8Repair welds.16 8Quality control17 8.1General17 8.2Quality control personnel qualifications.17 8.3Measuring and test equipment.17 8.4Quality control for specific equipment and components17 ISO 13535:2000(E) i
11、v ISO 2000 All rights reserved 8.5Dimensional verification .22 8.6Proof load test22 8.7Hydrostatic testing.23 8.8Functional testing23 9Equipment.24 9.1General24 9.2Hoisting sheaves24 9.3Travelling blocks25 9.4Block-to-hook adapters.26 9.5Connectors, link-adapters and drill-pipe elevator-adapters26 9
12、.6Drilling hooks.26 9.7Elevator links26 9.8Elevators.26 9.9Rotary swivels29 9.10Power swivels.36 9.11Power subs.36 9.12Wireline anchors37 9.13Drill-string motion compensators37 9.14Pressure vessels and piping 37 9.15Anti-friction bearings.37 9.16Safety clamps when capable of being used as hoisting e
13、quipment37 10Marking .38 10.1Product marking.38 10.2Rating marking.38 10.3Composite equipment marking38 10.4Component traceability.38 10.5Serialization38 10.6Marking method .38 11Documentation.38 11.1General38 11.2Documentation to be kept by the manufacturer.39 11.3Documentation to be delivered with
14、 the equipment 39 Annex A (normative) Supplementary requirements41 A.1General41 A.2SR 1 Proof load test.41 A.3SR 2 Low temperature test41 A.4SR 3 Data book.41 A.5SR 4 Additional volumetric examination of castings.42 A.6SR 5 Volumetric examination of wrought material.42 Annex B (normative) Guide doll
15、ies43 B.1General43 B.2Principal loading conditions and corresponding safety factors 43 B.3Loads and load combinations43 B.4Fatigue considerations44 B.5Special safety precautions44 Annex C (informative) Guidance for qualification of heat-treatment equipment45 C.1Temperature tolerance 45 C.2Furnace ca
16、libration45 C.3Instruments.46 Bibliography47 -,-,- ISO 13535:2000(E) ISO 2000 All rights reservedv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally c
17、arried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wor
18、k. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical co
19、mmittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights
20、. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 13535 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum and natural gas industries, Subcommittee SC 4, Drilling and production equipme
21、nt. Annexes A and B form a normative part of this International Standard. Annex C is for information only. ISO 13535:2000(E) vi ISO 2000 All rights reserved Introduction This International Standard is based upon API Spec 8C 2, 3rdedition, December 1997. Users of this International Standard should be
22、 aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment or engineering solutions for the individual application. This may be particul
23、arly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard and provide details. -,-,- INTERNATIONAL STANDARDISO 13535:2000(E) ISO 2000 All rights reserved1 Petroleum and natural gas i
24、ndustries Drilling and production equipment Hoisting equipment 1Scope This International Standard provides requirements for the design, manufacture and testing of hoisting equipment suitable for use in drilling and production operations. This International Standard is applicable to the following dri
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13535 2000
链接地址:https://www.31doc.com/p-3774700.html