ISO-15812-2001.pdf
《ISO-15812-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-15812-2001.pdf(12页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 15812:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 15812 First edition 2001-09-01 Continuous mill flat rolled products Guidelines for improved ordering communication Produits plats lamins en continu Lignes directrices visant amliorer les changes entre client et fournisseur au mom
2、ent de la commande dun produit Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 08:42:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15812:2001(E) PDF disclaimer
3、This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept
4、therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file
5、; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2001 All rights r
6、eserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the req
7、uester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO L
8、icensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 08:42:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15812:2001(E) ISO 2001 All rights reservediii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standar
9、ds bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organi
10、zations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in
11、 the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility th
12、at some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15812 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 12, Continuous mill flat
13、 rolled products. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 08:42:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15812:2001(E) iv ISO 2001 All rights reser
14、ved Introduction This International Standard applies to those products defined by the specifications which are the responsibility of ISO TC 17/SC 12. The field of application is limited to the product types, features and options of those specifications. Because of the extensive product customization
15、 that is often required for each order, it is important to develop a system for communication of the order requirements before mass production is initiated. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 0
16、4/23/2007 08:42:40 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 15812:2001(E) ISO 2001 All rights reserved1 Continuous mill flat rolled products Guidelines for improved ordering communication 1Scope This International Standard is a guideline int
17、ended to assist purchasers of continuous mill flat rolled products in assuring that their steel purchase orders meet the order entry needs of the producing steel mills so that the shipped material successfully satisfies the purchasers requirements. It is intended to assist purchasers in considering
18、key types of option in order to ensure full definition of the product requirements. The limited number of examples is to assist in ascertaining what type of information is required and cannot include every possible option available. This International Standard is to be used in support of direct comm
19、unication with the steel mills technical and commercial specialists. They are best able to assist purchasers in defining the specifics of each order. This International Standard does not replace or modify the section in each specification which defines information to be supplied by the purchaser. 2T
20、erms and definitions For the purposes of this International Standard, the following terms and definitions apply. 2.1Customer identification 2.1.1 company name name to which ownership shall be transferred 2.1.2 billing address address to which the invoice shall be sent 2.1.3 shipping address address
21、to which the steel shall be sent NOTEEven if the steel is sold FOB the mill or processor, the location of conversation to a part or product should be indicated to the steel mill or processor. 2.1.4 contact name person or persons who can be contacted to receive or supply information 2.2Product descri
22、ption 2.2.1 base product base material being purchased, e.g. hot-rolled, cold-rolled, hot-dipped, galvanized Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 08:42:40 MDTNo reproduction or network
23、ing permitted without license from IHS -,-,- ISO 15812:2001(E) 2 ISO 2001 All rights reserved 2.2.2 general quality general quality level of the steel being purchased, e.g. commercial quality, deep drawing quality, structural quality 2.2.3 quantity quantity being purchased in pounds, tons, kilograms
24、 or tonnes 2.2.4 finish general finish being purchased, e.g. pickled and oiled on hot-rolled sheet product, matte on cold-rolled sheet product, bright finish on strip and minimum spangle on galvanized coated product 2.2.5 end use part description to which the steel is to be converted, e.g.?42 linepi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 15812 2001
链接地址:https://www.31doc.com/p-3775572.html