ISO-14443-4-2001.pdf
《ISO-14443-4-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-14443-4-2001.pdf(54页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO/IEC 14443-4 First edition 2001-02-01 AMENDMENT 1 2006-03-1 5 Identification cards - Contactless integrated circuit(s) cards - Proximity cards - Part 4: Transmission protocol AMENDMENT 1 : Handling of reserved fields and values Cartes didentification - Cartes a circuit(s) i
2、ntgr(s) sans contact - Cartes de proximit - Partie 4: Protocole de transmission AMENDEMEN J 7: Maniement de champs et valeurs rservs Reference number ISOIIEC 14443-4:2001 /Amd.l:2006(E) 0 ISOIIEC 2006 ISO/IEC 14443-4:2001/Amd.l:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In
3、accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adob
4、es licensing policy. The IS0 Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the sofiware products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for
5、printing. Every care has been taken to ensure that the file is suitable for use by IS0 member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. O ISOIIEC 2006 All rights reserved. Unless otherwise specified, no par
6、t of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IS0 at the address below or ISOs member body in the country of the requester. IS0 copyright office Case postale 5
7、6 CH-I21 1 Geneva 20 Tel. + 41 22 749 O 1 11 Fax +41227490947 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii O ISOIIEC 2006 - All rights reserved ISO/IEC 14443-4:2001/Amd.l:2006(E) Foreword IS0 (the International Organization for Standardization) and IEC (the International Elect
8、rotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of IS0 or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of techni
9、cal activity. IS0 and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with IS0 and IEC, also take part in the work. In the field of information technology, IS0 and IEC have established a joint technic
10、al committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circ
11、ulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS0 and IEC shall not be held
12、 responsible for identifying any or all such patent rights. Amendment 1 to ISO/IEC 14443-4:2001 was prepared by Joint Technical Committee ISO/IEC JTC 1, information technology, Subcommittee SC 17, Cards and personal identification. As part of maintaining ISO/IEC 14443-4:2001, a need was raised to be
13、tter clarify the handling of fields and values reserved by ISO/IEC for future use. This Amendment addresses the required document enhancements. ISO/IEC 14443-4:2001 defines certain fields and values as Reserved for Future Use (RFU) by new ISO/IEC rules that may be added in later versions. This Amend
14、ment includes clarification that products in conformity with ISO/IEC 14443-4:2001 shall not improperly use RFU fields and values, plus documentation of product behaviour that, when followed by PICC and PCD designs commenced after publication of ISO/IEC 14443-4:2001, should assist with backward compa
15、tibility and interoperability for future definition by IS0 of RFU fields and values. Consequently, many of the references to “should” may be changed into a definitive “shall” in the second edition of ISO/IEC 14443-4:2001; thus, it is recommended to implement them at this time. O ISOIIEC 2006 - All r
16、ights reserved iii -,-,- ISO/IEC 14443-4:2001/Amd.l:2006(E) Identification cards - Contactless integrated circuit(s) cards - Proximity cards - Part 4: Transmission protocol AMENDMENT 1 : Handling of reserved fields and values Page 3, Clause 4 “Symbols and abbreviated terms” Replace the definition of
17、 RFU with the following: “Reserved for Future Use by ISO/IEC Page 6, Subclause 5.1 “Request for answer to select” Add the following paragraphs as the last paragraphs in the subclause: “A PCD setting FSDI = 9-F is not compliant with this standard. A received value of FSDI = 9-F should be interpreted
18、by the PICC as FSDI = 8 (FSD = 256 bytes). A PCD setting CID = 15 is not compliant with this standard. For PICC behaviour see 5.6.1.2 (c).” Page 7, Subclause 5.2.3 “Format byte” Add the following paragraphs as the last paragraphs in the subclause: “A PICC setting FSCI = 9-F is not compliant with thi
19、s standard. A received value of FSCI = 9-F should be interpreted by the PCD as FSCI = 8 (FSC = 256 bytes). A PICC not setting b8 to O is not compliant with this standard. The PCD should ignore b8 and its interpretation of any other field of the whole frame shall not change.” Page 8, Subclause 5.2.4
20、“Interface byte TA(1)” Add the following paragraphs as the last paragraphs in the subclause: “A PICC setting b4 = 1 is not compliant with this standard. A received value of TA(1) with b4 = 1 should be interpreted by the PCD as (b8 to bl) = (00000000)b (only -106 kbits in both directions).” Page 9, S
21、ubclause 5.2.5 “Interface byte TB(1)” O ISO/IEC 2006 -All rights reserved 1 -,-,- ISO/IEC 14443-4:2001/Amd.l:2006(E) Add the following paragraphs as the last paragraphs in the subclause: “A PICC setting SFGI = 15 is not compliant with this standard. Until the RFU value 15 is assigned by SO, a PCD re
22、ceiving SFGI = 15 should interpret it as SFGI = O. A PICC setting FWI = 15 is not compliant with this standard. Until the RFU value 15 is assigned by SO, a PCD receiving FWI = 15 should interpret it as FWI = 4.” Page 9, Subclause 5.2.6 “Interface byte TC(1)” Add the following paragraphs as the last
23、paragraphs in the subclause: “A PICC setting (b8 to b3) (0001)b and/or setting (b8 to b6) (0001)b and/or receiving (b8 to b6) (0OOO)b is not compliant with this standard. A PICC receiving (b8 to b5) (10)b of an S-block is not compliant with this standard. O of an I-block is not compliant with this s
24、tandard. 1 of an R-block is not compliant with this standard. Page 17, Subclause 7.1.1.2 “Card identifier field” Add the following paragraphs as the last paragraphs in the second list item starting “The bits b6 and b5 .” : “A PICC or PCD setting (b6,b5) (0O)b shall be treated as a protocol error.” O
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 14443 2001
链接地址:https://www.31doc.com/p-3775766.html