ISO-16367-2008.pdf
《ISO-16367-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-16367-2008.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 16367:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 16367 Second edition 2008-03-01 Tools for pressing Guide plates U- and V-blocks Outillage de presse Plaques de guidage Blocs en U et en V Copyright International Organization for Standardization Provided by IHS under license wit
2、h ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:30:49 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16367:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or vie
3、wed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in
4、 this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable
5、for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utiliz
6、ed in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +
7、41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:30:49 MDTNo reproduction or net
8、working permitted without license from IHS -,-,- ISO 16367:2008(E) ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally
9、carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wo
10、rk. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Inte
11、rnational Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of t
12、he elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16367 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and
13、 replaces the first edition (ISO 16367:2001) which has been technically revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:30:49 MDTNo reproduction or networking permitted without licens
14、e from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:30:49 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 16367:2008(E) ISO 20
15、08 All rights reserved 1 Tools for pressing Guide plates U- and V-blocks 1 Scope This International Standard specifies the main dimensions and tolerances of guiding plates, U- and V-blocks, to be used in press tools. It also specifies the designation of U- and V-blocks. 2 Normative references The fo
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 16367 2008
链接地址:https://www.31doc.com/p-3775882.html