ISO-1234-1997.pdf
《ISO-1234-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-1234-1997.pdf(7页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 1234 Second edition 1997-11-01 Split pins Goupilles fendues This material is reproduced from IS0 documents under International Organization for Standardization (ISO) Copyright License number lHSllCCll996. Not for resale. No part of these IS0 documents may be reproduced in
2、any form, electronic retrieval system or otherwise, except as allowed in the copyright law of the country of use, or with the prior written consent of IS0 (Case postale 66,lZll Geneva 20, Switzerland, Fax +4122 734 10 79), IHS or the IS0 Licensers members. Reference number IS0 1234:1997(E) Copyright
3、 International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 02:49:22 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 1234:1997(E) Foreword IS0 (the International Organiz
4、ation for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established
5、 has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
6、Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 1234 was prepared by Technical Committee ISOIT
7、C 2, Fasteners. This second edition cancels and replaces the first edition (IS0 1234:1976), which has been technically revised. Q IS0 1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,
8、 including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 l CH-1211 GetWe 20 l Switzerland Internet centraliso.ch x.400 cxh; a=rlOOnet; piso; o=isocs; s=central Printed in Switzerland ii Copyright Internati
9、onal Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 02:49:22 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 IS0 1234:1997(E) Split pins 1 scope Thi
10、s International Standard specifies the characteristics of split pins. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All stan
11、dards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0
12、 3269:1988, Fasteners -Acceptance inspection. IS0 4042:-l, Fasteners - Electroplated coatings. IS0 9717:1990, Phosphate conversion coatings for metals - Method of specifying requirements. 3 Dimensions See figure 1, table 1 and table 2 Figure 1 Shape of ends optional -+I- 1) To be published. (Revisio
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1234 1997
链接地址:https://www.31doc.com/p-3775905.html