ISO-16969-1999.pdf
《ISO-16969-1999.pdf》由会员分享,可在线阅读,更多相关《ISO-16969-1999.pdf(94页珍藏版)》请在三一文库上搜索。
1、Reference number ISO/IEC 16969:1999(E) ISO 1999 INTERNATIONAL STANDARD ISO/IEC 16969 First edition 1999-10-01 Information technology Data interchange on 120 mm optical disk cartridges using +RW format Capacity: 3,0 Gbytes and 6,0 Gbytes Technologies de linformation change de donnes sur cartouches de
2、 disque optique de 120 mm utilisant le format +RW Capacit: 3,0 Gbytes et 6,0 Gbytes Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 01:13:47 MDTNo reproduction or networkin
3、g permitted without license from IHS -,-,- ISO/IEC 16969:1999(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed o
4、n the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products us
5、ed to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please
6、inform the Central Secretariat at the address given below. ISO/IEC 1999 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writin
7、g from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO/IEC 1999 All rights reserved Copyright
8、 International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 01:13:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 16969:1999(E) ISO/IEC 1999 All rights rese
9、rvediii ContentsPage Forewordviii 1. Scope1 2. Conformance1 2.1. Optical Disk1 2.2. Generating system1 2.3. Receiving system1 2.4. Compatibility statement1 3. Normative reference1 4. Definitions2 5. Conventions and notations3 5.1. Representation of numbers3 5.2. Names3 6. List of acronyms4 7. Genera
10、l description of the optical disk4 8. General Requirements5 8.1. Environments5 8.1.1. Test environment5 8.1.2. Operating environment5 8.1.3. Storage environment6 8.1.4. Transportation6 8.2. Safety requirements6 8.3. Flammability6 9. Reference Drive6 9.1. Optical system6 9.2. Optical beam7 9.3. Read
11、channel 17 9.4. Disk clamping8 9.5. Rotation of the disk8 9.6. Tracking channel (Read channel 2)8 9.6.1. Normalized servo transfer function8 9.6.2. Reference Servo for Axial Tracking9 9.6.3. Reference Servo for Radial Tracking10 10. Dimensional characteristics11 10.1. Reference Planes11 10.2. Overal
12、l dimensions11 10.3. First transition area12 10.4. Second transition area12 10.5. Clamping Zone12 10.6. Third transition area12 10.7. Information Zone13 10.8. Rim area13 10.9. Remark on tolerances13 11. Mechanical characteristics14 11.1. Mass14 Copyright International Organization for Standardizatio
13、n Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 01:13:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 16969:1999(E) iv ISO/IEC 1999 All rights reserved 11.2. Moment of inertia14 11.3. Dynami
14、c imbalance14 11.4. Axial runout15 11.5. Radial runout15 12. Optical characteristics15 12.1. Index of refraction15 12.2. Thickness of the substrate15 12.3. Reflectivity16 12.4. Birefringence16 12.5. Angular deviation16 13. Data format17 13.1. Data Frames17 13.1.1. Identification Data (ID)18 13.1.2.
15、ID Error Detection Code (IED)19 13.1.3. RSV19 13.1.4. Error Detection Code (EDC)19 13.2. Scrambled Frames19 13.3. ECC Blocks20 13.4. Recording Frames22 13.5. Modulation and NRZI conversion22 13.6. Physical Sectors23 13.7. Layout of a Recording Unit Block (RUB)24 13.7.1. Sync Frames used for linking2
16、4 13.7.2. Start Position Shift (SPS)25 13.7.3. Recording Unit Block position25 13.8. d.c. component suppression control26 14. Track format26 14.1. Track shape26 14.2. Track path27 14.3. Track pitch27 14.4. Track number27 14.5. Track layout27 14.5.1. Segment layout28 14.5.2. AFCMs29 15. General descr
17、iption of the Information Zone31 16. Layout of the Information Zone31 16.1. Physical Sector Numbers (PSNs)32 17. Lead-in Zone33 17.1. Initial Zone34 17.2. Reference Code Zone34 17.3. Buffer Zone 134 17.4. Control Data Zone35 17.4.1. Physical format information35 17.4.2. Disk manufacturing informatio
18、n39 17.4.3. Content provider information39 17.5. Buffer Zone 239 17.6. Connection Zone39 17.7. Guard Zone 140 17.8. Inner Disk Test Zone40 17.9. Inner Drive Test Zone40 17.10. Guard Zone 240 17.11. DMA Zone 140 17.12. Inner Disk Identification Zone40 17.13. DMA Zone 240 18. Data Zone40 Copyright Int
19、ernational Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 01:13:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 16969:1999(E) ISO/IEC 1999 All rights reserved
20、v 19. Lead-out Zone40 19.1. DMA Zone 341 19.2. Outer Disk Identification Zone41 19.3. DMA Zone 441 19.4. Guard Zone 341 19.5. Outer Drive Test Zone41 19.6. Outer Disk Test Zone41 19.7. Guard Zone 441 20. The use of the Defect Management Areas41 20.1. Defect Management Areas42 20.2. Primary Defect Li
21、st (PDL)42 20.3. Secondary Defect List (SDL)43 20.4. Assignment of Logical Sector Numbers (LSNs)45 20.5. Slipping and Linear Replacement algorithms and requirements45 21. Disk Control ECC Blocks (DCBs)45 21.1. Format of Disk Control ECC Blocks45 22. General47 23. Method of testing47 23.1. Environmen
22、t47 23.2. Reference Drive47 23.2.1. Optics and mechanics47 23.2.2. Read power47 23.2.3. Read channels47 23.2.4. Tracking47 23.3. Definition of signals47 24. Characteristics of the groove signals48 24.1. Push-pull signal48 24.2. Track Cross signal48 24.3. Phase depth48 24.4. Normalized wobble signal4
23、9 24.5. Characteristics of the wobble49 24.6. Characteristics of the Alternating Fine Clock Marks (AFCM)49 25. Method of testing49 25.1. Environment49 25.2. Reference Drive49 25.2.1. Optics and mechanics49 25.2.2. Read power49 25.2.3. Read channels49 25.2.4. Tracking50 25.2.5. Scanning velocity50 25
24、.3. Write conditions for Rewritable area50 25.3.1. Write pulse waveform50 25.3.2. Write power50 25.3.3. Measurement conditions50 25.4. Jitter50 25.5. Channel bit length51 25.6. Phase depth51 25.7. Definition of signals51 25.7.1. High frequency signals (HF)51 25.7.2. Modulated amplitude51 25.7.3. Ref
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 16969 1999
链接地址:https://www.31doc.com/p-3776188.html