ISO-16154-2005.pdf
《ISO-16154-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-16154-2005.pdf(46页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 16154:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 16154 First edition 2005-04-15 Tractors and machinery for agriculture and forestry Installation of lighting, light signalling and marking devices for travel on public roadways Tracteurs et matriels agricoles et forestiers Instal
2、lation des dispositifs dclairage, de signalisation lumineuse et didentification pour circulation sur route Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 23:28:45 MDTNo reproduc
3、tion or networking permitted without license from IHS -,-,- ISO 16154:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to an
4、d installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the softwar
5、e products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is f
6、ound, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission
7、in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Co
8、pyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 23:28:45 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16154:2005(E) ISO 2005 All rights reserved ii
9、i Contents Page Forewordiv 1 Scope1 2 Normative references .1 3 Terms and definitions.1 4 General requirements.6 Annex A (normative) Lighting, marking, signalling and retro-reflective devices Data sheets9 Annex B (normative) Colorimetric characteristics of illuminating and signalling lights28 Annex
10、C (normative) Forward visibility of red lights and rearward visibility of white lights.30 Annex D (normative) Lamp surfaces, reference axis, centre of reference and angles of geometric visibility32 Annex E (informative) Other requirements for lighting and marking devices .34 Annex F (informative) Te
11、chnical specifications of lighting and marking devices covered by other standards.38 Bibliography .39 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 23:28:45 MDTNo reproduction
12、or networking permitted without license from IHS -,-,- ISO 16154:2005(E) iv ISO 2005 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norm
13、ally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in t
14、he work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare
15、 International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some
16、 of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16154 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. Copyright
17、 International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/07/2007 23:28:45 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 16154:2005(E) ISO 2005 All ri
18、ghts reserved 1 Tractors and machinery for agriculture and forestry Installation of lighting, light signalling and marking devices for travel on public roadways 1 Scope This International Standard specifies the characteristics and installation of lighting and marking devices on agricultural and fore
19、stry tractors, self-propelled agricultural machines, agricultural trailers and trailed machines when operated on public roads. It is not applicable to purpose-built forestry machines as defined in ISO 6814 or to motor vehicles such as automobiles, buses, trucks and their trailers. 2 Normative refere
20、nces The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 303, Road vehicles Installation of light
21、ing and light signalling devices for motor vehicles and their trailers 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 303 and the following apply. 3.1 angles of geometric visibility angles which determine the field of the minimum solid angle in whic
22、h the apparent surface of the lamp must be visible NOTE 1 The field of the solid angle is determined by the segments of the sphere of which the centre coincides with the centre of reference of the lamp and the equator is parallel with the ground. These segments are determined in relation to the refe
23、rence axis. The horizontal angles correspond to the longitude and the vertical angles to the latitude. There must be no obstacle on the inside of the angles of geometric visibility to the propagation of light from any part of the apparent surface of the lamp observed from infinity. NOTE 2 If measure
24、ments are taken closer to the lamp, the direction of observation must be shifted parallel to achieve the same accuracy. NOTE 3 On the inside of the angles of geometric visibility, no account is taken of obstacles already present when the lamp was type-approved. NOTE 4 If, when the lamp is installed,
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 16154 2005
链接地址:https://www.31doc.com/p-3776209.html