ISO-16851-2004.pdf
《ISO-16851-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-16851-2004.pdf(10页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 16851:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 16851 First edition 2004-12-15 Textile conveyor belts Determination of the net length of an endless (spliced) conveyor belt Courroies transporteuses carcasse textile Mthode de mesurage de la longueur nette dune courroie transpor
2、teuse sans fin (jonctionne) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:52:16 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16851:2004(E) P
3、DF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, p
4、arties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relati
5、ve to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 200
6、4 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the coun
7、try of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved Copyright International Organization for Standardization Provided by IHS under li
8、cense with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:52:16 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16851:2004(E) ISO 2004 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldw
9、ide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on th
10、at committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in
11、accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard r
12、equires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16851 was prepared by the
13、European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 41, Pulleys and belts (including veebelts), Subcommittee SC 3, Conveyor belts, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this d
14、ocument, read “.this European Standard.” to mean “.this International Standard.”. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:52:16 MDTNo reproduction or networking permit
15、ted without license from IHS -,-,- ISO 16851:2004(E) iv ISO 2004 All rights reserved Contents Page Forewordv 1 Scope 1 2 Apparatus .1 3 Procedure .1 4 Calculation and expression of results.2 5 Test report 2 Bibliography3 Copyright International Organization for Standardization Provided by IHS under
16、license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:52:16 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16851:2004(E) ISO 2004 All rights reserved v Foreword This document (EN ISO 16851:2004) has been prepared by Technical Com
17、mittee CEN/TC 188 “Conveyor belts”, the secretariat of which is held by BSI, in collaboration with Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 16851 2004
链接地址:https://www.31doc.com/p-3776293.html