ISO-20860-1-2008.pdf
《ISO-20860-1-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-20860-1-2008.pdf(18页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 20860-1:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 20860-1 First edition 2008-10-15 Road vehicles 50 impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements Vhicules routiers Interface de systme de connexion de frquence radio de 50
2、Partie 1: Dimensions et exigences lectriques Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E)
3、 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
4、 parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info rela
5、tive to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYR
6、IGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below
7、or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved Copyright International Organization for Standardi
8、zation Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references.
9、 1 3 Terms and definitions. 1 4 Dimensions and coding . 2 4.1 General. 2 4.2 Male connector 2 4.3 Female connector. 2 4.4 Coding ribs 2 4.5 Mechanical and colour codings of the connection system 2 4.6 Multiple interfaces 2 5 Designations . 9 6 Characteristic values 9 7 Test procedures 11 Bibliograph
10、y. 12 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) iv ISO 2008 All rights reserved Forewo
11、rd ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic
12、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el
13、ectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to t
14、he member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for id
15、entifying any or all such patent rights. ISO 20860-1 was prepared by Technical Committee ISO/TC 22, Road vehicles. ISO 20860 consists of the following parts, under the general title Road vehicles 50 impedance radio frequency connection system interface: Part 1: Dimensions and electrical requirements
16、 Part 2: Test procedures Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 20860-1:2008
17、(E) ISO 2008 All rights reserved 1 Road vehicles 50 impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements 1 Scope This part of ISO 20860 specifies male and female connectors of the 50 impedance system interface for radio frequency applications in road v
18、ehicles, and ensures communication to and within road vehicles. It specifies dimensional and electrical requirements and characteristics required for interchange ability. This connection system can be applied in all relevant equipment and cable connections of road vehicles. 2 Normative references Th
19、e following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 20860-2, Road vehicles 50 impedance radio frequ
20、ency connection system interface Part 2: Test procedures 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 male contact pin contact contact intended to make electrical engagement on its outer surface and which will enter a female contact (socke
21、t) 3.2 female contact socket contact contact intended to make electrical engagement on its inner surface and which will accept entry of a male contact (pin) 3.3 male connector pin connector connector containing a male centre contact Copyright International Organization for Standardization Provided b
22、y IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) 2 ISO 2008 All rights reserved 3.4 female contact socket connector connector containing a female centre contact
23、 4 Dimensions and coding 4.1 General Unspecified details shall be shown as required in accordance with the characteristics defined in Clause 6. 4.2 Male connector The dimension of the cable connector (CC) and the connector on apparatus (CoA) of the 50 connection system shall conform to Figures 1, 2
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 20860 2008
链接地址:https://www.31doc.com/p-3776315.html