ISO-11106-2-1997.pdf
《ISO-11106-2-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-11106-2-1997.pdf(8页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 11106-2 First edition 1997-03-01 Photography - Slide trays for projectors - Part 2: Straight slide tray, closed type (Japanese design) Photographie - Paniers chargeurs de diapositives pour projecteurs - Partie 2: Panier chargeur droit de diapositives, type ferm6 (conceptio
2、n japonaise) Reference number IS0 11106-2: 1997(E) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 23:26:02 MDTNo reproduction or networking permitted without license from IHS -,
3、-,- IS0 11106=2:1997(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in
4、 a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commis
5、sion (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Internatio
6、nal Standard IS0 11106-2 was prepared by Technical Committee lSO/TC 42, Photography. IS0 11106 consists of the following parts, under the general title Photography - Slide trays for projectors: - Part I: Straight slide tray, open type (European design) - Par? 2: Straight slide tray, closed type (Jap
7、anese design) Annex A of this part of IS0 11106 is for information only. 0 IS0 1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissi
8、on in writing from the publisher. International Organization for Standardization Case postale 56 l CH-1211 Geneve 20 l Switzerland Internet central iso.ch x.400 c=ch; a=400net; p=iso; o=isocs; s=central Printed in Switzerland ii Copyright International Organization for Standardization Provided by IH
9、S under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 23:26:02 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 IS0 11106-2: 1997(E) Photography - Slide trays for projectors - Part 2: Straight slide tray
10、, closed type (Japanese design) 1 Scope This part of IS0 11106 specifies the essential dimensions of a straight slide tray, closed type (Japanese design), for projector slides of the preferred international nominal size 5 cm x 5 cm complying with IS0 1755, with a capacity of 36 slides or 50 slides.
11、In this design, the slide tray is placed sideways into the projector and the slides are pushed sideways into the projector. Slides cannot be taken out of the tray when the tray is inserted in the projector. This part of IS0 11106 is intended to facilitate the manufacture, use and interchangeability
12、of straight slide trays in different slide projectors which are designed for this type of tray. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 11106. At the time of publication, the editions indicated
13、 were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 11106 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid Internationa
14、l Standards. I SO 54: 1977, Cylindrical gears for general and for heavy engineering - Modules and diametral pitches. IS0 1622-l :I 994, Plastics - Polystyrene (PS) moulding and extrusion materials - Par? I: Designation system and basis for specifications. IS0 1755: 1987, Photography - Projector slid
15、es - Dimensions. IS0 2768-l :I 989, General tolerances - Par? I: Tolerances for linear and angular dimensions without individual tolerance indications. 3 Capacity The capacity of the straight slide tray, closed type, shall be either 36 slides or 50 slides. 4 Dimensions 4.1 Rack teeth The dimensions
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11106 1997
链接地址:https://www.31doc.com/p-3776341.html