ISO-16818-2008.pdf
《ISO-16818-2008.pdf》由会员分享,可在线阅读,更多相关《ISO-16818-2008.pdf(40页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 16818:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 16818 First edition 2008-02-15 Building environment design Energy efficiency Terminology Conception de lenvironnement des btiments Rendement dnergie Terminologie Copyright International Organization for Standardization Provided
2、by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16818:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this fi
3、le may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat
4、 accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure th
5、at the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2008 The reproduction of the terms and definitions contained in this International Standard is permitted in teachi
6、ng manuals, instruction booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are: that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar public
7、ations offered for sale; and that this International Standard is referenced as the source document. With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, witho
8、ut permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All righ
9、ts reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16818:2008(E) ISO 2008 All rights reserved iii C
10、ontents Page Foreword iv Introduction v 1 Scope. 1 2 Normative references. 1 3 Terms and definitions 2 Bibliography. 32 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproduction
11、 or networking permitted without license from IHS -,-,- ISO 16818:2008(E) iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is nor
12、mally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in
13、the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepar
14、e International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that som
15、e of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16818 was prepared by Technical Committee ISO/TC 205, Building environment design. Copyright International Organization for Standardization Pro
16、vided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 16818:2008(E) ISO 2008 All rights reserved v Introduction This International Standard is intended to provide general ter
17、ms and definitions used in building environment design. Other standards produced by ISO/TC 205 can contain additional definitions more specific to the needs of the individual standard. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/
18、5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 03:48:31 MDTNo reproductio
19、n or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 16818:2008(E) ISO 2008 All rights reserved 1 Building environment design Energy efficiency Terminology 1 Scope This International Standard gives terms and definitions for use in the design of energy-efficient buildin
20、gs. This International Standard is applicable to new buildings and retrofitted existing buildings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the lates
21、t edition of the referenced document (including any amendments) applies. ISO 6707-1, Building and civil engineering Vocabulary Part 1: General terms ISO 7345, Thermal insulation Physical quantities and definitions ISO 7730, Ergonomics of the thermal environment Analytical determination and interpret
22、ation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria ISO 9229, Thermal insulation Vocabulary ISO 9251, Thermal insulation Heat transfer conditions and properties of materials Vocabulary ISO 9288, Thermal insulation Heat transfer by radiation Physic
23、al quantities and definitions ISO 9346, Hygrothermal performance of buildings and building materials Physical quantities for mass transfer Vocabulary ISO 13789, Thermal performance of buildings Transmission and ventilation heat transfer coefficients Calculation method ISO 137901), Energy performance
24、 of buildings Calculation of energy use for space heating and cooling ISO 15927-6, Hygrothermal performance of buildings Calculation and presentation of climatic data Part 6: Accumulated temperature differences (degree-days) ISO 16813, Building environment design Indoor environment General principle
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 16818 2008
链接地址:https://www.31doc.com/p-3776350.html