ISO-13563-1-2001.pdf
《ISO-13563-1-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-13563-1-2001.pdf(16页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 13563-1:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 13563-1 First edition 2001-03-01 Single side loading fork-lift trucks Part 1: Stability tests Chariots lvateurs fourche chargement latral sur un ct Partie 1: Essais de stabilit Copyright International Organization for Standardi
2、zation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 01:45:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13563-1:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance wi
3、th Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing
4、policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Eve
5、ry care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publicati
6、on may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva
7、20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale,
8、04/21/2007 01:45:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13563-1:2001(E) ISO 2001 All rights reservediii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of
9、preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,
10、 in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft Inte
11、rnational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO
12、 13563 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 13563-1 was prepared by Technical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2, Safety of powered industrial trucks. This part of ISO
13、13563 has been prepared using EEC 89/240 Method 5 as a basis. ISO 13563 consists of the following parts, under the general title Single side loading fork-lift trucks: Part 1: Stability tests Part 2: Additional stability tests for trucks handling freight containers of 6 m length and above Copyright I
14、nternational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 01:45:58 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization P
15、rovided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 01:45:58 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 13563-1:2001(E) ISO 2001 All rights reserved1 Single side loading fork-lift tru
16、cks Part 1: Stability tests 1Scope This part of ISO 13563 specifies basic tests to verify the stability of single side loading fork-lift trucks with tiltable or non-tiltable mast or fork arms. It is applicable to trucks fitted with fork arms and/or attachments. This part of ISO 13563 is not applicab
17、le to trucks that handle suspended loads that can swing freely. 2Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this part of ISO 13563. For dated references, subsequent amendments to, or revisions of, any of th
18、ese publications do not apply. However, parties to agreements based on this part of ISO 13563 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to
19、applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 5353:1995, Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point. 3Purpose of tests 3.1Normal operating conditions The basic tests specified in this part of I
20、SO 13563 ensure that the type of truck specified has satisfactory stability when reasonably and appropriately used under normal operating conditions, as follows: a)operating (travelling and stacking) on substantially firm, smooth, level and prepared surfaces; b)travelling with the mast or fork arms
21、tilted backwards and the load retracted and in the lowered (travelling) position, or resting on the load-carrying deck; c)stacking with the mast substantially vertical and the fork arms substantially horizontal; d)operating with the load centre of gravity approximately on the centre plane between th
22、e mast uprights. 3.2Operating in conditions other than normal When the operating conditions differ from those specified in 3.1, it is necessary to use either a)a truck complying with other parts of ISO 13563 covering different specific conditions, or b)a truck whose stability is agreed upon between
23、the interested parties; this agreed stability shall not be less than that required by the tests specified for normal operating conditions in 3.1. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Res
24、ale, 04/21/2007 01:45:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13563-1:2001(E) 2 ISO 2001 All rights reserved 4Stability tests 4.1Test requirements The stability of single side loading fork-lift trucks shall be verified by one of the procedures specified in 4.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 13563 2001
链接地址:https://www.31doc.com/p-3776383.html