ISO-10438-1-2007.pdf
《ISO-10438-1-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-10438-1-2007.pdf(68页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 10438-1:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 10438-1 Second edition 2007-12-15 Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries Part 1: General requirements Industries du ptrole, de la ptrochimie et du
2、 gaz naturel Systmes de lubrification, systmes dtanchit, systmes dhuile de rgulation et leurs auxiliaires Partie 1: Exigences gnrales ISO 10438-1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but sh
3、all not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area
4、. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by
5、 ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any
6、form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749
7、09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved ISO 10438-1:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms, abbreviated terms and definitions . 2 3.1 Terms and defi
8、nitions. 2 3.2 Abbreviated terms 8 4 General. 10 4.1 Dimensions and units. 10 4.2 Design 10 4.3 System selection. 10 4.4 Pressure design code. 10 4.5 Basic design 10 4.6 Welding 11 4.7 Statutory requirements 11 4.8 Documentation requirements 11 5 Piping. 11 5.1 General. 11 5.2 Oil piping . 18 5.3 In
9、strument piping and tubing 18 5.4 Process piping 18 5.5 Intercoolers and aftercoolers 19 6 Instrumentation, control and electrical systems. 20 6.1 General. 20 6.2 Alarm, shutdown and control systems. 20 6.3 Instrumentation. 23 6.4 Electrical systems. 28 7 Inspection testing, and preparation for ship
10、ment. 29 7.1 General. 29 7.2 Inspection 30 7.3 Testing . 32 7.4 Preparation for shipment. 33 8 Vendors data 34 8.1 General. 34 8.2 Proposals. 35 8.3 Contract data. 36 Annex A (informative) Datasheets 39 Annex B (informative) Symbols 40 Annex C (informative) Vendor drawing and data requirements (VDDR
11、) 42 Annex D (informative) Oil or gas filter performance and oil-system cleanliness testing. 46 Annex E (informative) International materials specifications 57 Annex F (informative) Explanation of reservoir levels. 58 Bibliography. 60 -,-,- ISO 10438-1:2007(E) iv ISO 2007 All rights reserved Forewor
12、d ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technica
13、l committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of ele
14、ctrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to th
15、e member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ide
16、ntifying any or all such patent rights. ISO 10438-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems. This second edition cancels and replaces the f
17、irst edition (ISO 10438-1:2003), which has been technically revised. ISO 10438 consists of the following parts, under the general title Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries: Part 1: General requirements Part 2: Special
18、-purpose oil systems Part 3: General-purpose oil systems Part 4: Self-acting gas seal support systems ISO 10438-1:2007(E) ISO 2007 All rights reserved v Introduction This part of ISO 10438 was developed jointly with API 614, 5th edition, together with the other three parts of ISO 10438. NOTE API 614
19、 is equivalent to ISO 10438 (all parts). Users of this part of ISO 10438 should be aware that further or differing requirements can be needed for individual applications. This part of ISO 10438 is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment
20、or engineering solutions for the individual application. This can be particularly appropriate where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this part of ISO 10438 and provide details. This part of ISO 10438 require
21、s the purchaser to specify certain details and features. A bullet () at the beginning of a clause or subclause indicates that either a decision is required or further information is to be provided by the purchaser. This information should be indicated on the datasheet(s); otherwise it should be stat
22、ed in the quotation request or in the order. In this International Standard, United States customary (USC) units are included in brackets for information. -,-,- INTERNATIONAL STANDARD ISO 10438-1:2007(E) ISO 2007 All rights reserved 1 Petroleum, petrochemical and natural gas industries Lubrication,
23、shaft-sealing and control-oil systems and auxiliaries Part 1: General requirements 1 Scope This part of ISO 10438 specifies general requirements for lubrication systems, oil-type shaft-sealing systems, dry-gas face-type shaft-sealing systems and control-oil systems for general- or special-purpose ap
24、plications. General-purpose applications are limited to lubrication systems. These systems can serve equipment such as compressors, gears, pumps and drivers. This part of ISO 10438 is intended to be used in conjunction with ISO 10438-2, ISO 10438-3 or ISO 10438-4, as appropriate. 2 Normative referen
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 10438 2007
链接地址:https://www.31doc.com/p-3776424.html