ISO-2113-1996.pdf
《ISO-2113-1996.pdf》由会员分享,可在线阅读,更多相关《ISO-2113-1996.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 2113:1996 TECHNICAL CORRIGENDUM 1 Published 2003-02-1 5 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION M W A P O f l H A R OPTAHHIHR no CTAHflAPTHIAUHH ORGANISATION INTERNATIONALE DE NORMALISATION Reinforcement fibres -Woven fabrics - Basis for a s pecif cat ion TECHNICAL
2、CORRIGENDUM 1 Renforts - Tissus - Base de spcification RECTIFICATIF TECHNIQUE I Technical Corrigendum 1 to IS0 21 13:1996 was prepared by Technical Committee ISOTC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. Page 1, Clause 2 Delete the reference to IS0 10548. In addition,
3、update the other normative references as follows: IS0 291: Insert the year of publication (1997) and delete footnote 1). IS0 1886: Replace by IS0 2859-1:1999, Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance qualify limit (AQL) for lot-by-lot inspecti
4、on, and IS0 3951 : 1989, Sampling procedures and charts for inspection by variables for percent nonconforming. IS0 4602: Insert the year of publication (1997) and delete footnote 2). IS0 46051978: Replace by IS0 3374:2000, Reinforcement products - Mats and fabrics - Determination of mass per unit ar
5、ea. IS0 5025:1978: Replace by IS0 5025: 1997, Reinforcement products - Woven fabrics - Determination of width and length. ICs 59.100.01 Ref. No. IS0 2113:1996/Cor.l:2003(E) O IS0 2003 -All rights reserved Published in Switzerland IS0 21 13: 1996/Cor.l:2003(E) Page 2, Definition 3.5 Add the following
6、 note: “NOTE The term is also used with reference to the type of weave.” Page 2, Clause 5 Replace “IS0 1886 by “IS0 2859-1 and IS0 3951”. Page 3, Subclause 7.2.2.1 Replace “IS0 4605 by “IS0 3374. Page 3, Subclause 7.2.3.2 Replace “IS0 10548 by “a suitable method”. 2 O IS0 2003 -All rights reserved -
7、,-,- IS0 2113 9h E 4851903 Obb1209 123 I NT E R NAT I O NA L STANDARD IS0 2113 Second edition 1996-06-01 Reinforcement fibres -Woven fabrics - Basis for a specification Renforts - TiCsus - Base de spcification Reference number IS0 21 13:1996(E) -,-,- IS0 2113 96 4851903 Obb1210 945 IS0 2113:1996(E)
8、Foreword IS0 (the International Organization for Standardization) is a worldwide fed- eration of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a
9、 technical committee has been established has the right to be rep- resented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 col- laborates closely with the International Electrotechnical Commission (IEC) on all m
10、atters of electrotechnical standardization. Draft International Standards adopted by the technical committees are cir- culated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0
11、21 13 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. This second edition cancels and replaces the first edition (IS0 21 13:1981), which has been technically revised. , O IS0 1996 All rights reserved. Unless otherwise specified, no pa
12、rt of this publication may be repro- duced or utilized in any form or by any means, electronic or mechanical, including photo- copying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56 CH-1 21 1 Genve 20 Switzerland Printe
13、d in Switzerland II -,-,- IS0 2333 96 4853903 ObbL2LL 883 W 0 IS0 Introduction IS0 2113:1996(E) A basis for a specification is intended to give guidance on the establish- ment of technical specifications for products of a given type. It should enumerate as completely as possible the points that shou
14、ld be considered at the time of drafting the specifications. The basis for a specification, therefore, does not in itself constitute a specification, but rather a model plan for the elaboration of specifications applying to a particular product, or to a family of products whose character- istics are
15、 closely related. These specifications may be established by a producer, supplier or user, or by a standardization organization. . 111 IS0 2113 96 E 4851903 ObbL2L2 718 INTERNATIONAL STANDARD 0 IS0 IS0 2113:1996(El Reinforcement fibres - Woven fabrics - Basis for a specification 1 Scope This Interna
16、tional Standard provides a basis for a specification applicable to fabrics woven from yarns (including single yarns, multiple-wound yarns, plied yarns, cabled yarns and rovings) made from textile glass, carbon or aramid and generally used for plastics reinforcements. This International Standard does
17、 not cover all require- ments for some specialized applications. If such other requirements are necessary, they are given, or will be given, in other International Standards. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provision
18、s of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to in- vestigate the possibility of applying the most recent editions of the standards
19、 indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 139:1973, Textiles - Standard atmospheres for conditioning and testing. IS0 291 :-I, Plastics - Standard atmospheres for conditioning and testing. IS0 1886: 1990, Reinforcement fibres - Sampli
20、ng plans applicable to received batches. IS0 1887:1995, Textile glass - Determination of combustible-matter content. IS0 2078: 1 993, Textile glass - Yarns - Designation. IS0 2797: 1 986, Textile glass - Rovings - Basis for a specification. IS0 3572:1976, Textiles - Weaves - Definitions of general t
21、erms and basic weaves. IS0 3598:1986, Textile glass - Yarns - Basis for a specification. IS0 4602:-*), Reinforcements - Woven fabrics - Determination of number of yarns per unit length of warp and weft. IS0 4603:1993, Textile glass - Woven fabrics - Determination of thickness. IS0 4604:1978, Textile
22、 glass - Woven fabrics - Determination of conventional flexural stiffness - Fixed angle flexometer method. IS0 4605:1978, Textile glass - Woven fabrics - Determination of mass per unit area. IS0 4606:1995, Textile glass - Woven fabric - Determination of tensile breaking force and elongation at break
23、 by the strip method. IS0 5025:1978, Textile glass - Woven fabric - Determination of width and length. IS0 10548:1994, Carbon fibre - Determination of size content. 1) To be published. (Revision of IS0 291 :1977) 2) To be published. (Revision of IS0 4602:1978) 1 -,-,- IS0 2113:1996(E) IS0 3 Definiti
24、ons For the purposes of this International Standard, the following definitions apply. 3.1 woven fabric: A reinforcement-fibre fabric made by interlacing at least two sets of threads perpendicu- larly to each other, or at some other specified angle, such interlacing being carried out by during weavin
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 2113 1996
链接地址:https://www.31doc.com/p-3776454.html