ISO-2328-2007.pdf
《ISO-2328-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-2328-2007.pdf(10页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 2328:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 2328 Third edition 2007-05-15 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions Chariots lvateurs fourche Bras de fourche tenons et tabliers porte-fourches Dimensions de montage ISO 2328:2007(E) P
2、DF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, p
3、arties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relati
4、ve to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 200
5、7 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the coun
6、try of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved ISO 2328:2007(E) ISO 2007 All rights reserved iii Foreword ISO (the International
7、 Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been est
8、ablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardiz
9、ation. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voti
10、ng. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such
11、 patent rights. ISO 2328 was prepared by Technical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2, Safety of powered industrial trucks. This third edition cancels and replaces the second edition (ISO 2328:1993), which has been technically revised. -,-,- INTERNATIONAL STANDARD ISO 2328:20
12、07(E) ISO 2007 All rights reserved 1 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions 1 Scope This International Standard specifies the dimensions of, and additional requirements for, fork carriers and hook-on type fork arms, to permit the interchangeability of thes
13、e fork arms and/or other attachments, relative to the truck-rated capacity and fork arm type, on fork-lift trucks up to and including 10 999 kg. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition ci
14、ted applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2331:1974, Fork lift trucks Hook-on type fork arms Vocabulary ISO 3691:1980, Powered industrial trucks Safety code1) 3 Terms and definitions For the purposes of this document, t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 2328 2007
链接地址:https://www.31doc.com/p-3776479.html