ISO-1167-4-2007.pdf
《ISO-1167-4-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-1167-4-2007.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 1167-4:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 1167-4 First edition 2007-11-01 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies Tubes, raccords et assemblages en
2、 matires thermoplastiques pour le transport des fluides Dtermination de la rsistance la pression interne Partie 4: Prparation des assemblages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for R
3、esale, 11/19/2007 05:18:43 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 1167-4:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typef
4、aces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Sy
5、stems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikel
6、y event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic o
7、r mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web
8、www.iso.org Published in Switzerland ii ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 11/19/2007 05:18:43 MSTNo reproduction or networking permitted wit
9、hout license from IHS -,-,- ISO 1167-4:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv 1 Scope 1 2 Normative references1 3 Principle1 4 Test pieces .2 4.1 Sampling.2 4.2 Fused assemblies2 4.3 Mechanical end-load-bearing assemblies.3 4.4 Adhesively bonded assemblies .3 4.5 Non-end-
10、load-bearing assemblies.4 4.6 Free length of pipes.5 4.7 Testing of tolerance variations.5 4.8 Measurement of dimensions5 Bibliography6 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale,
11、 11/19/2007 05:18:43 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 1167-4:2007(E) iv ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of
12、preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,
13、 in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main t
14、ask of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attent
15、ion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1167-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the tran
16、sport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic specifications. ISO 1167 consists of the following parts, under the general title Thermoplastics pipes, fittings and assemblies for the conveyance of
17、 fluids Determination of the resistance to internal pressure: Part 1: General method Part 2: Preparation of pipe test pieces Part 3: Preparation of components Part 4: Preparation of assemblies Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IH
18、S Employees/1111111001, User=Wing, Bernie Not for Resale, 11/19/2007 05:18:43 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 1167-4:2007(E) ISO 2007 All rights reserved 1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids
19、Determination of the resistance to internal pressure Part 4: Preparation of assemblies 1 Scope This part of ISO 1167 specifies the procedure for the preparation of both end-load-bearing and non-end-load-bearing assemblies, for the determination of their resistance to internal hydrostatic pressure ac
20、cording to ISO 1167-1. NOTE The assemblies consist of a selection of pipes, fittings, valves, fusion joints or adhesively bonded joints. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appl
21、ies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 3126, Plastics piping
22、systems Plastics components Determination of dimensions ISO 11413, Plastics pipes and fittings Preparation of test piece assemblies between polyethylene (PE) pipe and electrofusion fitting ISO 11414, Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece as
23、semblies by butt fusion EN 1066, Adhesives Sampling EN 1067, Adhesives Examination and preparation of samples for testing 3 Principle Test pieces comprising a selection of pipes, fittings, valves, fusion joints or adhesively bonded joints connected to form a pressure-resistant assembly are condition
24、ed at the specified test temperature and then subjected to the internal hydrostatic pressure according to ISO 1167-1 for a specified period of time, or until the test piece(s) fail(s). The number of test pieces, conditioning and details of the test report are as given in ISO 1167-1. Copyright Intern
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1167 2007
链接地址:https://www.31doc.com/p-3776485.html