ISO-22762-3-2005.pdf
《ISO-22762-3-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-22762-3-2005.pdf(72页珍藏版)》请在三一文库上搜索。
1、ICS 83.140.99; 91.120.25 Ref. No. ISO 22762-3:2005/Cor.1:2006(E) ISO 2006 All rights reserved Published in Switzerland INTERNATIONAL STANDARD ISO 22762-3:2005 TECHNICAL CORRIGENDUM 1 Published 2006-07-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION Elas
2、tomeric seismic-protection isolators Part 3: Applications for buildings Specifications TECHNICAL CORRIGENDUM 1 Appareils dappuis structuraux en lastomre pour protection sismique Partie 3: Applications pour btiments Spcifications RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 22762-3:2005 wa
3、s prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). Page 16, Subclause 6.5.5.2, item c) Add a new paragraph: “The shear strain amplitude shall be 0.” Page 17, Subclause 6.5.6.2, item c) Delete “The shear strain amplitude shall be 0
4、.” Replace “Other test conditions” with “The test conditions”. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 22:57:55 MDTNo reproduction or networking permitted without l
5、icense from IHS -,-,- ISO 22762-3:2005/Cor.1:2006(E) 2 ISO 2006 All rights reserved Page 20, Subclause 6.6.3, item b) Replace “Other conditions can be used by agreement between the structural engineer and the manufacturer” by “Other conditions for NR and CR can be used by agreement between the struc
6、tural engineer and the manufacturer”. Add a new sentence: “Test conditions for other elastomers shall be as recommended by the manufacturer and agreed by the structural engineer.” Page 47, Annex F After Equation (F.5), replace “isolator” by “rubber layer”. Copyright International Organization for St
7、andardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 22:57:55 MDTNo reproduction or networking permitted without license from IHS -,-,- Reference number ISO 22762-3:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 22762-3 Fir
8、st edition 2005-07-15 Elastomeric seismic-protection isolators Part 3: Applications for buildings Specifications Appareils dappuis structuraux en lastomre pour protection sismique Partie 3: Applications pour btiments Spcifications Copyright International Organization for Standardization Provided by
9、IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 22:57:55 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 22762-3:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes lic
10、ensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The I
11、SO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has b
12、een taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be rep
13、roduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22
14、 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04
15、/2007 22:57:55 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 22762-3:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword. v Introduction. vi 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 2 4 Symbols and abbreviated terms . 4 5 Classificati
16、on. 8 5.1 General. 8 5.2 Classification by construction 8 5.3 Classification by ultimate properties 10 5.4 Classification by tolerance on shear properties . 10 6 Requirements 11 6.1 General. 11 6.2 Type tests and routine tests 12 6.3 Functional requirements 12 6.4 Design compressive force and design
17、 shear displacement 13 6.5 Performance requirements 13 6.6 Rubber material requirements. 19 6.7 Dimensional requirements. 20 6.8 Requirements on steel used for flanges and reinforcing plates . 21 7 Design rules 22 7.1 General. 22 7.2 Shape factor 22 7.3 Compression and shear properties 23 7.4 Ultima
18、te properties. 24 7.5 Reinforcing steel plates . 26 7.6 Connections 27 8 Manufacturing tolerances 27 8.1 General. 27 8.2 Measuring instruments 27 8.3 Plan dimensions . 27 8.4 Product height. 28 8.5 Flatness . 29 8.6 Horizontal offset 30 8.7 Plan dimensions of flanges . 31 8.8 Flange thickness. 31 8.
19、9 Tolerances on positions of flange bolt holes 32 9 Marking and labelling. 32 9.1 General. 32 9.2 Information to be provided 32 9.3 Additional requirements 33 9.4 Marking and labelling examples 33 10 Test methods. 33 11 Quality assurance. 33 Copyright International Organization for Standardization P
20、rovided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 22:57:55 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 22762-3:2005(E) iv ISO 2005 All rights reserved Annex A (normative) Tensile stress in reinforci
21、ng steel plate 34 Annex B (informative) Confirmation list.36 Annex C (informative) Determination of ultimate property diagram based on experimental results38 Annex D (informative) Minimum recommended physical properties of rubber material41 Annex E (informative) Effect of inner-hole diameter and sec
22、ond shape factor on shear properties 43 Annex F (informative) Determination of compressive properties of elastomeric isolators46 Annex G (informative) Determination of shear properties of elastomeric isolators49 Annex H (informative) Method of predicting buckling limit at large deformations54 Annex
23、I (informative) Design of fixing bolts and flanges .60 Bibliography .63 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 22:57:55 MDTNo reproduction or networking permitted
24、without license from IHS -,-,- ISO 22762-3:2005(E) ISO 2005 All rights reserved v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out throug
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 22762 2005
链接地址:https://www.31doc.com/p-3776575.html