ISO-2342-2003.pdf
《ISO-2342-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-2342-2003.pdf(10页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 2342 Second edition 2003-12-01 Reference number ISO 2342:2003(E) ISO 2003 Slotted headless screws with shank Vis sans tte fendues, ft ISO 2342:2003(E) ii ISO 2003 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes lic
2、ensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The I
3、SO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has b
4、een taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be rep
5、roduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22
6、 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland -,-,- ISO 2342:2003(E) ISO 2003 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The
7、work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gover
8、nmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. Th
9、e main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote
10、. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2342 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and r
11、eplaces the first edition (ISO 2342:1972), which has been technically revised. -,-,- . iv -,-,- INTERNATIONAL STANDARDISO 2342:2003(E) ISO 2003 All rights reserved 1 Slotted headless screws with shank 1Scope This International Standard specifies the characteristics of slotted headless screws with sh
12、ank with threads from M1 up to and including M10. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e.g. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3, ISO 8839 and ISO 4759-1. 2Normati
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 2342 2003
链接地址:https://www.31doc.com/p-3776648.html