ISO-15877-5-2009.pdf
《ISO-15877-5-2009.pdf》由会员分享,可在线阅读,更多相关《ISO-15877-5-2009.pdf(16页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 15877-5:2009(E) ISO 2009 INTERNATIONAL STANDARD ISO 15877-5 Second edition 2009-03-15 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system Systmes de canalisations en plastique pour les i
2、nstallations deau chaude et froide Poly(chlorure de vinyle) chlor (PVC-C) Partie 5: Aptitude lemploi du systme Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/07/2009 23:56:41 MDTNo reproduction or n
3、etworking permitted without license from IHS -,-,- ISO 15877-5:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and insta
4、lled on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software produ
5、cts used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, p
6、lease inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfil
7、m, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009
8、All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/07/2009 23:56:41 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15877-5:2009(E) ISO 2009 All rights
9、reserved iii Contents Page Foreword iv Introduction. vi 1 Scope . 1 2 Normative references. 1 3 Terms and definitions, symbols and abbreviated terms 2 4 Fitness for purpose of the joints and the piping system 2 4.1 General. 2 4.2 Internal pressure test . 3 4.3 Pull-out test . 6 4.4 Thermal cycling.
10、7 4.5 Pressure cycling. 7 4.6 Leaktightness under vacuum 8 Bibliography. 9 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/07/2009 23:56:41 MDTNo reproduction or networking permitted without license
11、from IHS -,-,- ISO 15877-5:2009(E) iv ISO 2009 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
12、 committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with
13、 the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Intern
14、ational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may
15、be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15877-5 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Techni
16、cal Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This part of ISO 15877 is part of a System S
17、tandard for plastics piping systems of a particular material for a specified application. There are a number of such System Standards. The System Standards are consistent with general standards on functional requirements and recommended practices for installation. This second edition cancels and rep
18、laces the first edition (ISO 15877-5:2003). ISO 15877 consists of the following parts 1), under the general title Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the s
19、ystem Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7) 1) This System Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made
20、 from different materials, intended to be used for hot and cold water installations, is covered by ENV 12108 2. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/07/2009 23:56:41 MDTNo reproduction or
21、networking permitted without license from IHS -,-,- ISO 15877-5:2009(E) ISO 2009 All rights reserved v At the date of publication of this part of ISO 15877, System Standards Series for piping systems of other plastics materials used for the same application are the following: ISO 15874 (all parts),
22、Plastics piping systems for hot and cold water installations Polypropylene (PP) ISO 15875 (all parts), Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) ISO 15876 (all parts), Plastics piping systems for hot and cold water installations Polybutylene (PB) IS
23、O 22391: 2) (all parts), Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) 2) To be published. (Revisions of ISO 22391-1:2007, ISO 22391-2:2007, ISO 22391-3:2007, ISO 22391-5:2007.) Copyright International Organization for Standardizat
24、ion Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/07/2009 23:56:41 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15877-5:2009(E) vi ISO 2009 All rights reserved Introduction The System Standard, of which this is Part 5, sp
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 15877 2009
链接地址:https://www.31doc.com/p-3776699.html