ISO-24034-2005.pdf
《ISO-24034-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-24034-2005.pdf(16页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 24034:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 24034 First edition 2005-10-01 Welding consumables Solid wires and rods for fusion welding of titanium and titanium alloys Classification Produits consommables pour le soudage Fils pleins et baguettes pleines pour le soudage par
2、 fusion du titane et des alliages de titane Classification Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproduction or networking permitted without license fro
3、m IHS -,-,- ISO 24034:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editi
4、ng. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be f
5、ound in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at t
6、he address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transm
7、itted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office C
8、ase postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. ii ISO 2005 All rights reserved Copyright International Organization for Standa
9、rdization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 24034:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword iv Introduction v 1
10、Scope . 1 2 Normative references. 1 3 Classification. 1 4 Symbols and requirements 1 5 Mechanical properties 2 6 Chemical analysis. 2 7 Retest. 2 8 Technical delivery conditions . 2 9 Designation . 6 Annex A (informative) Explanation of classification symbols for chemical composition 7 Copyright Int
11、ernational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 24034:2005(E) iv ISO 2005 All rights reserved Foreword I
12、SO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical c
13、ommittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electr
14、otechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the m
15、ember bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identi
16、fying any or all such patent rights. ISO 24034 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 3, Welding consumables. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972
17、545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 24034:2005(E) ISO 2005 All rights reserved v Introduction This International Standard proposes a classification in order to designate wire electrodes, wires and rods in terms of t
18、heir chemical composition. For titanium-welding consumables, there is no unique relationship between the product form (wire electrodes, wires or rods) and the welding process used (gas-shielded metal arc welding, gas tungsten arc welding, plasma arc welding or laser welding). For this reason, wire e
19、lectrodes, wires and rods may be classified in terms of their chemical composition. In this International Standard, the symbol of the welding process is not used, because a) different joining processes are performed with the same chemical component consumable, and b) the producer is not able to dete
20、rmine the process symbol before shipping. Also, it should be noted that the mechanical properties of all-weld metal test specimens or welded joints produced by welding consumables will vary from those obtained in production joints because of differences in welding procedure and the base-metal alloy.
21、 For this reason, the mechanical properties of all-weld metal or welded joints for titanium-welding consumables are not specified in this classification. Requests for an official interpretation of technical aspects of this International Standard should be directed to the secretariat of ISO/TC 44/SC
22、3 via the users member body in the users country; a listing of these bodies can be found at www.iso.org. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproducti
23、on or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 08:08:38 MDTNo reproduction or networking permitted without license from
24、 IHS -,-,- INTERNATIONAL STANDARD ISO 24034:2005(E) ISO 2005 All rights reserved 1 Welding consumables Solid wires and rods for fusion welding of titanium and titanium alloys Classification 1 Scope This International Standard specifies requirements for the classification of solid wires and rods for
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 24034 2005
链接地址:https://www.31doc.com/p-3776730.html