ISO-14617-13-2004.pdf
《ISO-14617-13-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-14617-13-2004.pdf(10页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 14617-13:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 14617-13 First edition 2004-11-15 Graphical symbols for diagrams Part 13: Devices for material processing Symboles graphiques pour schmas Partie 13: Dispositifs de transformation des matriaux Copyright International Organizat
2、ion for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:51:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14617-13:2004(E) PDF disclaimer This PDF file may contain embedded typefaces
3、. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing
4、 Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized
5、 for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part
6、 of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56
7、 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545
8、001 Not for Resale, 04/24/2007 19:51:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14617-13:2004(E) ISO 2004 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member
9、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental
10、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directiv
11、es, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
12、casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14617-13 was prepared by Technical Committee ISO/TC 10, Technical product documen
13、tation, Subcommittee SC 10, Process plant documentation and tpd-symbols. ISO 14617 consists of the following parts, under the general title Graphical symbols for diagrams: Part 1: General information and indexes Part 2: Symbols having general application Part 3: Connections and related devices Part
14、4: Actuators and related devices Part 5: Measurement and control devices Part 6: Measurement and control functions Part 7: Basic mechanical components Part 8: Valves and dampers Part 9: Pumps, compressors and fans Part 10: Fluid power converters Part 11: Devices for heat transfer and heat engines Pa
15、rt 12: Devices for separating, purification and mixing Part 13: Devices for material processing Part 14: Devices for transport and handling of material Part 15: Installation diagrams and network maps Copyright International Organization for Standardization Provided by IHS under license with ISO Lice
16、nsee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:51:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 14617-13:2004(E) iv ISO 2004 All rights reserved Introduction The purpose of ISO 14617 in its final form is the creation of a library of harmon
17、ized graphical symbols for diagrams used in technical applications. This work has been, and will be, performed in close co-operation between ISO and IEC. The ultimate result is intended to be published as a standard common to ISO and IEC, which their technical committees responsible for specific app
18、lication fields can use in preparing International Standards and manuals. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 19:51:22 MDTNo reproduction or networking permitted with
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 14617 13 2004
链接地址:https://www.31doc.com/p-3776750.html