ISO-2346-2001.pdf
《ISO-2346-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-2346-2001.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 2346:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 2346 Fifth edition 2001-12-15 Road vehicles M14 1,25 compact spark-plugs with flat seating and 19 mm hexagon and their cylinder head housing Vhicules routiers Bougies dallumage M14 1,25 compactes sige plat et hexagone de 19 mm et
2、 leur logement dans la culasse ISO 2346:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer pe
3、rforming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this
4、 PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Centra
5、l Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at
6、the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved ISO 2346:2001(E) ISO 2001 All rights
7、 reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject
8、 for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)
9、on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees
10、 are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO sh
11、all not be held responsible for identifying any or all such patent rights. ISO 2346 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 1, Ignition equipment. This fifth edition cancels and replaces the fourth edition (ISO 2346:1991), which has been technically revised. INT
12、ERNATIONAL STANDARD ISO 2346:2001(E) ISO 2001 All rights reserved 1 Road vehicles M14 1,25 compact spark-plugs with flat seating and 19 mm hexagon and their cylinder head housing 1 Scope This International Standard specifies the main characteristics of M14 1,25 compact spark-plugs with flat seating
13、and 19 mm hexagon and their cylinder head housing, for use with spark-ignition engines. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments
14、 to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition
15、of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 68-1, ISO general purpose screw threads Basic profile Part 1: Metric screw threads ISO 261, ISO general-purpose metric screw threads General plan ISO 965-1:1998, I
16、SO general purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 14508:1997, Road vehicles Spark-plugs Terminals 3 Terminals The spark-plug terminal may be eithe
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 2346 2001
链接地址:https://www.31doc.com/p-3776753.html