ISO-3977-8-2002.pdf
《ISO-3977-8-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-3977-8-2002.pdf(18页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 3977-8:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 3977-8 First edition 2002-07-01 Gas turbines Procurement Part 8: Inspection, testing, installation and commissioning Turbines gaz Spcifications pour lacquisition Partie 8: Contrle, essais, installation et mise en service ISO 39
2、77-8:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloadin
3、g this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the Gener
4、al Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given
5、below. ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member bo
6、dy in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved ISO 3977-8:2002(E) ISO 2002 All rights reserved iii Contents Page Forew
7、ord.iv 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 General principles .2 5 Inspection.3 5.1 General3 5.2 Material inspection3 5.3 Mechanical inspection 4 6 Testing4 6.1 General4 6.2 Hydrostatic test4 6.3 Functional/operating tests5 6.4 Optional tests.10 7 Preparation for storage an
8、d shipment 10 7.1 General10 7.2 Preparation.11 8 Installation and commissioning.11 ISO 3977-8:2002(E) iv ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing In
9、ternational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison
10、with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of techn
11、ical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn
12、 to the possibility that some of the elements of this part of ISO 3977 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3977-8 was prepared by Technical Committee ISO/TC 192, Gas turbines. ISO 3977 consists of the following par
13、ts, under the general title Gas turbines Procurement: Part 1: General and definitions Part 2: Standard reference conditions and ratings Part 3: Design requirements Part 4: Fuels and environment Part 5: Applications for petroleum and natural gas industries Part 7: Technical information Part 8: Inspec
14、tion, testing, installation and commissioning Part 9: Reliability, availability, maintainability and safety INTERNATIONAL STANDARD ISO 3977-8:2002(E) ISO 2002 All rights reserved 1 Gas turbines Procurement Part 8: Inspection, testing, installation and commissioning 1 Scope This part of ISO 3977 stat
15、es the principles for systems and procedures to assure the integrity of a packagers product and services. It gives guidance on the inspection, testing, installation and commissioning required for the package and packaged equipment. It outlines the responsibilities between the purchaser and packager
16、for inspection, coordination, reporting and recording. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 3977. For dated references, subsequent amendments to, or revisions of, any of these publ
17、ications do not apply. However, parties to agreements based on this part of ISO 3977 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies
18、. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 2314:1989, Gas turbines Acceptance tests ISO 3977-1:1997, Gas turbines Procurement Part 1: General introduction and definitions ISO 3997-2:1997, Gas turbines Procurement Part 2: Standard reference conditions
19、and ratings ISO 3977-3:2002, Gas turbines Procurement Part 3: Design requirements ISO 3997-4:2002, Gas turbines Procurement Part 4: Fuels and environment ISO 4406:1999, Hydraulic fluid power Fluids Method for coding the level of contamination by solid particles ISO 6190:1988, Acoustics Measurement o
20、f sound pressure levels of gas turbine installations for evaluating environmental noise Survey method ISO 10442:1) , Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors for general refinery service ISO 11042-1:1996, Gas turbines Exhaust gas emission
21、 Part 1: Measurement and evaluation ISO 11086:1996, Gas turbines Vocabulary 1) To be published. -,-,- ISO 3977-8:2002(E) 2 ISO 2002 All rights reserved ISO 13709:1), Centrifugal pumps for petroleum, petrochemical, and natural gas industries ISO 13691:2001, Petroleum and natural gas industries High-s
22、peed special-purpose gear units IEC 60034-1:1983, Rotating electrical machines Part 1: Rating and performance IEC 60034-4:1985; Rotating electrical machines Part 4: Methods for determining synchronous machine quantities from tests 3 Terms and definitions For the purposes of this part of ISO 3977, th
23、e terms and definitions given in ISO 3977-1, ISO 3977-3, ISO 3977-4 and ISO 11086 and the following apply. 3.1 inspection process by which it is demonstrated that materials, components, assemblies or complete packages satisfy one or more particular specification requirements of the packager or purch
24、aser NOTE This may include verificational documentation, reports, material certificates, chemical analyses, physical or dimensional checks, build records, visual checks and/or results of documented inspections and tests including any other non- destructive evaluation (NDE) methods or techniques that
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 3977 2002
链接地址:https://www.31doc.com/p-3777424.html