《ISO-3732-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-3732-2003.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 3732:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 3732 Fourth edition 2003-11-01 Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 S (supplementary) for vehicles with 12 V nominal supply voltage Vhicules routiers Connect
2、eurs pour liaisons lectriques entre vhicules tracteurs et vhicules tracts Connecteur 7 contacts de type 12 S (supplmentaire) pour les vhicules tension nominale de 12 V ISO 3732:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file
3、may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat ac
4、cepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that
5、the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in an
6、y form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 74
7、9 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved -,-,- ISO 3732:2003(E) ISO 2003 All rights reserved iii Contents Page Forewordiv 1 Scope1 2 Normative references .1 3 Terms and definitions.2 4 Dimensions2 5 Application of connector5 6 Tests and
8、 specific requirements.7 Bibliography .9 -,-,- ISO 3732:2003(E) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carr
9、ied out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
10、ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Internat
11、ional Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the e
12、lements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3732 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. This fourth edition cancels an
13、d replaces the third edition (ISO 3732:1997), which has been technically revised. INTERNATIONAL STANDARD ISO 3732:2003(E) ISO 2003 All rights reserved 1 Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 S (supplementary) for vehicles with 12
14、 V nominal supply voltage 1 Scope This International Standard specifies the dimensions of, and requirements for, 7-pole connectors of type 12 S and their contact allocation for the electrical connection of towing (passenger cars or light commercial vehicles) and towed vehicles with 12 V nominal supp
15、ly voltage, thus ensuring interchangeability. A 12 S connector is intended to be used in addition to a 12 N connector according to ISO 1724 where more than 7 poles are required. NOTE For new developments and where more than 7 poles are required, as an alternative to the use of the 7-pole connector a
16、ccording to this International Standard and ISO 1724, the use of 13-pole connector in accordance with ISO 11446 1 may be required. 2 Normative references The following referenced documents are indispensable for application of this document. For dated references, only the edition cited applies. For u
17、ndated references, the latest edition of the referenced document (including any amendments) applies. ISO 1103, Road vehicles Coupling balls for caravans and light trailers Dimensions ISO 1724, Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 1
18、2 N (normal) for vehicles with 12 V nominal supply voltage ISO 4091:2003, Road vehicles Connectors for the electrical connection of towing and towed vehicles Definitions, tests and requirements ISO 4141 (all parts), Road vehicles Multi-core connecting cables -,-,- ISO 3732:2003(E) 2 ISO 2003 All rig
19、hts reserved 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4091 apply. 4 Dimensions 4.1 General Details not specified are at the manufacturers discretion. Pins in sockets and plugs shall be slotted to allow compression over a minimum length of 8,5
20、mm when plug and socket are engaged. 4.2 Plug Dimensions of the plug shall be in accordance with Figure 1. The plug shall have five spring pins, numbered 1, 3, 4, 6 and 7, and two tubes, numbered 2 and 5. 4.3 Socket Dimensions of the socket shall be in accordance with Figure 2. The socket shall have
21、 five tubes, numbered 1, 3, 4, 6 and 7, and two spring pins, numbered 2 and 5. The cover is shown in the open position: it shall close automatically when the plug is disconnected. -,-,- ISO 3732:2003(E) ISO 2003 All rights reserved 3 Dimensions in millimetres a For Pin No. 7. b For the tubes. c For
22、Pin Nos. 1, 3, 4 and 6. d Pitch circle diameter. e Slot for key. f For 19 min. g Rear view of the terminals. Figure 1 Plug -,-,- ISO 3732:2003(E) 4 ISO 2003 All rights reserved Dimensions in millimetres a Contact No. 1. b Other housing designs are permitted provided that the dimensions are within th
23、e maximum diameter. c Pitch circle diameter. d Position of the cover with the plug engaged. e Key. f Chamfer 60 to 90. g Tube Nos. 1, 3, 4 and 6. h Tube No. 7. i Pins. j Plug-retaining lip. k Cover view. Figure 2 Socket ISO 3732:2003(E) ISO 2003 All rights reserved 5 5 Application of the connector 5
24、.1 Connector positions and free space A socket shall be mounted at the rear of the towing vehicle and the position shall be in accordance with the dimensions necessary for the compatibility of mechanical coupling devices according to ISO 1103. The minimum free space around the connection shall be in
25、 accordance with Figure 3. Dimensions in millimetres a Horizontal free space. b Socket cover. c Connecting cable. d Attachment of the cable in the plug. e Plug. f Socket. g The angle of maximum 60 shall extend across the horizontal free space. Figure 3 Free space 5.2 Distinguishing marking The 12 S
26、connectors shall be distinguished from 12 N connectors (see ISO 1724) by means of a different colouring of at least the insulating parts. A light and permanent colour, preferably white, shall be used for the 12 S connectors. 5.3 Contact allocation The contact allocation of the connector shall be in
27、accordance with Table 1. ISO 3732:2003(E) 6 ISO 2003 All rights reserved Table 1 Contact allocation Contact No. Function Core insulation colour (for information) 1 Reversing light a Yellow 2 Reserved for future allocation Blue 3 Return for Contact No. 4 White 4 Permanent power supply Green 5 Reserve
28、d for future allocation Brown 6 Power supply controlled by ignition switch Red 7 Return for Contact No. 6 Black a The common return for the circuit of this contact will normally be by contact No. 3 of the 12 N connector according to ISO 1724. 5.4 Contact designation The contact designation numbers s
29、hall be permanently marked on the inside of the socket cover, and on the terminal faces of both plug and socket. The character size shall not be less than 2 mm. However, where limited space is available, a smaller size may be used on the terminal face. 5.5 Terminals The terminals at the rear side of
30、 the pins and tubes shall be capable of accepting cables with the following nominal cross-sectional areas. Contact Nos. 1 and 5: 1,5 mm2. Contact Nos. 3, 4, 6 and 7: 2,5 mm2. 5.6 Connecting cable The connecting cable shall meet the requirements of the applicable parts of ISO 4141. 5.7 Protection of
31、disconnected plug A means of storing the plug when disconnected shall be provided on the towed vehicle, intended to protect the plug from the ingress of water or foreign bodies and from accidental damage. -,-,- ISO 3732:2003(E) ISO 2003 All rights reserved 7 6 Tests and specific requirements 6.1 Gen
32、eral Connectors in accordance with this International Standard shall be tested in the sequences given in Table 2. For test procedures, see ISO 4091. They shall meet the requirements of ISO 4091, except where specified differently in the following subclauses. Table 2 Test sequences Sample group Test
33、A B C D E Visual examination 1, 8 1, 11 1, 8 1, 10 1, 11 Dimensional check 2 Connection 3 2 2 2 2 Disconnection 7 10 7 9 9 Locking device and cable retention strength 4 3, 9 3, 8 3, 8 Lateral strength at low temperature 6 Current carrying capacity 4 Connection resistance 4, 7 3, 6 4, 7 4, 7 Current
34、cycling 5 Withstand voltage 5, 8 6 5, 10 Static load 5 Endurance 6 Temperature/humidity cycling 6 Salt spray 5 6.2 Locking device and cable retention strength Perform the locking device and cable retention strength test according to ISO 4091. Apply the specified force to the cable retention only of
35、a disengaged plug. Apply a force of (250 5) N. 6.3 Connection and disconnection Perform the connection and disconnection tests according to ISO 4091. The connection forces shall be u 200 N, and the disconnection force shall be between 50 N and 200 N. 6.4 Salt spray Perform the salt spray test accord
36、ing to ISO 4091:2003, except that arrangements b) and c) shall not apply. -,-,- ISO 3732:2003(E) 8 ISO 2003 All rights reserved 6.5 Temperature/humidity cycling Perform the temperature/humidity cycling test according to ISO 4091:2003, but with Steps d) to g) modified as follows: d) Lower tc to (25 2
37、) C within 2,5 h. e) Hold tc at (25 2) C for 2 h. f) Raise tc to (75 2) C within 1,5 h. g) Hold tc at (75 2) C for 2 h. 6.6 Endurance Perform the endurance test according to ISO 4091, but for 1 000 cycles only. -,-,- ISO 3732:2003(E) ISO 2003 All rights reserved 9 Bibliography 1 ISO 114461 ), Road vehicles Connectors for the electrical connection of towing and towed vehicles 13-pole connectors for vehicles with 12 V nominal supply voltage 1) To be published. (Revision of ISO 11446:1995) ISO 3732:2003(E) ICS 43.040.10 Price based on 9 pages ISO 2003 All rights reserved
链接地址:https://www.31doc.com/p-3777439.html