《ISO-6149-1-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-6149-1-2006.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 6149-1:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 6149-1 Second edition 2006-02-15 Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal Raccordements pour t
2、ransmissions hydrauliques et applications gnrales Orifices et lments mles filetage mtrique ISO 261 et joint torique Partie 1: Orifices joint torique dans un logement tronconique Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755
3、100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unl
4、ess the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademar
5、k of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. I
6、n the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, in
7、cluding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publ
8、ished in Switzerland ii ISO 2006 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:
9、2006(E) ISO 2006 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member b
10、ody interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electro
11、technical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted
12、by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent r
13、ights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6149-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. This second edition cancels and replaces the first edition (ISO 6
14、149-1:1993), which has been technically revised. ISO 6149 consists of the following parts, under the general title Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing: Part 1: Ports with truncated housing for O-ring seal Part 2: Di
15、mensions, design, test methods and requirements for heavy-duty (S series) stud ends Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends Part 4: Dimensions, design, test methods and requirements of external and internal hexport plugs Copyright International O
16、rganization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) iv ISO 2006 All rights reserved Introduction In hydraulic fluid power
17、systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. In general applications, a fluid (liquid or gas) may be conveyed under pressure. Components are connected through their threaded ports by fluid conductor connectors to tubes and pipes or to hose
18、connectors and hoses. Ports are an integral part of fluid power components, such as pumps, motors, valves, cylinders, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, ISO/TC 131/SC 4 recommends that the ISO 6149 series be used because these Intern
19、ational Standards specify ports and stud ends with metric threads and O-ring sealing and because the subcommittee would like to help users by recommending one preferred system. ISO/TC 131/SC 4 further recommends that threaded ports and stud ends in accordance with the ISO 1179 series, ISO 9974 serie
20、s and ISO 11926 series not be used for new designs in hydraulic fluid power applications; these International Standards are maintained because they specify ports and stud ends that are currently used in hydraulic systems worldwide. Copyright International Organization for Standardization Provided by
21、 IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 6149-1:2006(E) ISO 2006 All rights reserved 1 Connections for hydraulic fluid power and general use Ports
22、 and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal 1 Scope This part of ISO 6149 specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2 and ISO 6149-3. Ports in accordance w
23、ith this part of ISO 6149 may be used at working pressures up to 63 MPa 630 bar1) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149-2 and ISO 6149-
24、3 for pressure ratings. Users of this part of ISO 6149 should ensure that there is sufficient material around the port to maintain the pressure. NOTE The Introduction of this part of ISO 6149 gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applicatio
25、ns. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 261, ISO general p
26、urpose metric screw threads General plan ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 2306, Drills for use prior to tapping screw threads ISO 55982), Fluid power systems and components Vocabulary ISO 6149-2, Connections for hydraulic fluid powe
27、r and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy- duty (S series) stud ends 1) 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2. 2) To be published. (Revision of ISO 5598:1985). Copyright International O
28、rganization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) 2 ISO 2006 All rights reserved ISO 6149-33), Connections for fluid pow
29、er and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends 3 Terms and definitions For the purposes of this part of ISO 6149, the terms and definitions given in ISO 5598 apply. 4
30、Dimensions Ports shall conform to the dimensions shown in Figure 1 and given in Table 1. Dimensions in millimetres, values for surface roughness in micrometres a Optional identification of port; see Figure 2 and Clause 7. b Pitch diameter. c This dimension only applies when tap drill cannot pass thr
31、ough entire boss. d Gauging. e Reference only. f Thread. Figure 1 Port 3) To be published. (Revision of ISO 6149-3:1993). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproducti
32、on or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) ISO 2006 All rights reserved 3 Table 1 Port dimensions Dimensions in millimetres Threada d2 d3b d4 d5 L1 L2c L3 L4 Z (d1 P) wided min. narrowe min. ref. 0,1 0 + 0,4 0 + min. max. min. 1 M8 1 17 14 3 12,5 9,1 1,6 11,5 1 10 1
33、2 M10 1 20 16 4,5 14,5 11,1 1,6 11,5 1 10 12 M12 1,5 23 19 6 17,5 13,8 2,4 14 1,5 11,5 15 M14 1,5f 25 21 7,5 19,5 15,8 2,4 14 1,5 11,5 15 M16 1,5 28 24 9 22,5 17,8 2,4 15,5 1,5 13 15 M18 1,5 30 26 11 24,5 19,8 2,4 17 2 14,5 15 M20 1,5g 33 29 27,5 21,8 2,4 2 14,5 15 M22 1,5 33 29 14 27,5 23,8 2,4 18
34、2 15,5 15 M27 2 40 34 18 32,5 29,4 3,1 22 2 19 15 M30 2 44 38 21 36,5 32,4 3,1 22 2 19 15 M33 2 49 43 23 41,5 35,4 3,1 22 2,5 19 15 M42 2 58 52 30 50,5 44,4 3,1 22,5 2,5 19,5 15 M48 2 63 57 36 55,5 50,4 3,1 25 2,5 22 15 M60 2 74 67 44 65,5 62,4 3,1 27,5 2,5 24,5 15 a Conforming to ISO 261, tolerance
35、 grade 6H in accordance with ISO 965-1. Tap drills in accordance with ISO 2306, class 6H. b For reference only. Connecting hole application may require a different size. c The tap drill depths given require the use of a bottoming tap to produce the specified full thread lengths. Where standard taps
36、are used, the tap drill depths shall be increased accordingly. d Spotface diameter with identification ridge. e Spotface diameter without identification ridge. f Preferred for diagnostic port applications. g For cartridge valve cavity applications only (see ISO 7789). Copyright International Organiz
37、ation for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) 4 ISO 2006 All rights reserved Dimensions in millimetres a Thread. Figure 2
38、Optional port identification Table 2 Optional port identification4) Dimensions in millimetres Thread d6 (d1 P) 0,5 0 + M8 1 14 M10 1 16 M12 1,5 19 M14 1,5 21 M16 1,5 24 M18 1,5 26 M20 1,5a 29 M22 1,5 29 M27 2 34 M30 2 38 M33 2 43 M42 2 52 M48 2 57 M60 2 67 a For cartridge valve cavities only (see IS
39、O 7789). 4) See Clause 7. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) ISO 2006 All rights
40、 reserved 5 5 Test methods Ports shall be tested along with stud ends in accordance with the test methods and requirements given in ISO 6149-2 and ISO 6149-3. For rated pressures lower than those specified in ISO 6149-2 and ISO 6149-3, the test pressures shall be agreed upon between the manufacturer
41、 and user. 6 Designation of ports The ports shall be designated by a) “Port”; b) reference to this part of ISO 6149, i.e. ISO 6149-1; c) thread size (d1 P). EXAMPLE A port in accordance with this part of ISO 6149, with a thread M18 1,5 is designated as follows: Port ISO 6149-1 - M18 1,5 7 Identifica
42、tion Each port in accordance with this part of ISO 6149 shall be identified by a raised ring conforming to the dimensions given in Figure 2 and Table 2, or by permanently marking “metric” or “M” next to the port, or by a permanent identification label on the component to read “ISO 6149-1 metric port
43、s”. 8 Identification statement (reference to this part of ISO 6149) It is strongly recommended to manufacturers who have chosen to conform to this International Standard that the following statement be used in test reports, catalogues and sales literature: “Ports conform to ISO 6149-1:2006, Connecti
44、ons for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal.” Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not fo
45、r Resale, 04/23/2007 02:09:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 6149-1:2006(E) 6 ISO 2006 All rights reserved Bibliography 1 ISO 1101, Technical drawings Geometrical tolerancing Tolerances of form, orientation, location and run-out Generalities, definition
46、s, symbols, indications on drawings 2 ISO 1179-15), Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports 3 ISO 1179-25), Connections for general use and fluid power Ports and stud ends with ISO 228-1
47、threads with elastomeric or metal-to-metal sealing Part 2: Heavy-duty (S series) and light-duty (L series) stud ends and elastomeric sealing (type E) 4 ISO 1179-35), Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) 5 ISO 1179-45), Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general u
链接地址:https://www.31doc.com/p-3778360.html