ISO-1641-1-2003.pdf
《ISO-1641-1-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-1641-1-2003.pdf(10页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 1641-1:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 1641-1 Second edition 2003-06-01 End mills and slot drills Part 1: Milling cutters with cylindrical shanks Fraises cylindriques 2 tailles et fraises rainurer Partie 1: Fraises queue cylindrique Copyright International Organizat
2、ion for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 20:13:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1641-1:2003(E) PDF disclaimer This PDF file may contain embedded typefaces.
3、In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing A
4、dobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized f
5、or printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part o
6、f this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 C
7、H-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/997254500
8、1 Not for Resale, 04/24/2007 20:13:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1641-1:2003(E) ISO 2003 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bod
9、ies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and
10、 non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,
11、Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies cast
12、ing a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1641-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2,
13、 Drills, reamers, milling cutters and milling machine accessories. This second edition cancels and replaces the first edition (ISO 1641-1:1978), which has been technically revised, in particular by the inclusion of threaded shanks. ISO 1641 consists of the following parts, under the general title En
14、d mills and slot drills: Part 1: Milling cutters with cylindrical shanks Part 2: Milling cutters with Morse taper shanks Part 3: Milling cutters with 7/24 taper shanks Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/
15、9972545001 Not for Resale, 04/24/2007 20:13:20 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 20:13:20
16、MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 1641-1:2003(E) ISO 2003 All rights reserved 1 End mills and slot drills Part 1: Milling cutters with cylindrical shanks 1 Scope This part of ISO 1642 specifies the general dimensions of the following
17、 milling cutters with plain cylindrical, flatted cylindrical and threaded shanks: end mills, flat-ended or ball-nosed standard series and long series; slot drills short series and standard series. The dimensional characteristics of cylindrical shanks are in accordance with ISO 3338-1, ISO 3338-2 and
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 1641 2003
链接地址:https://www.31doc.com/p-3778376.html