ISO-5655-2000.pdf
《ISO-5655-2000.pdf》由会员分享,可在线阅读,更多相关《ISO-5655-2000.pdf(13页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 5655:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 5655 Third edition 2000-10-01 Photography Industrial radiographic films (roll and sheet) and metal intensifying screens Dimensions Photographie Films radiographiques industriels (rouleaux et feuilles) et crans intensificateurs en
2、mtal Dimensions Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5655:2000(E) PDF disclaimer
3、 This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept
4、 therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the fil
5、e; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2000 All rights
6、reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the re
7、quester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO
8、Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5655:2000(E) ISO 2000 All rights reservediii ContentsPage Foreword.iv 1Scope 1 2Normative references1 3Conditions for measurement of dimens
9、ions1 4Films in rolls.1 5Films in sheets.2 6Package marking .4 7Dimensions of intensifying screens5 Annex A (informative) Quantity packaging for sheets 8 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not
10、 for Resale, 04/22/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5655:2000(E) iv ISO 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). Th
11、e work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gov
12、ernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
13、Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this I
14、nternational Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 5655 was prepared by Technical Committee ISO/TC 42, Photography. This third edition cancels and replaces the second edition (ISO 5655
15、:1993), of which it constitutes a technical revision based upon ANSI/BAPM IT1.15-1994. Annex A of this International Standard is for information only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not fo
16、r Resale, 04/22/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 5655:2000(E) ISO 2000 All rights reserved1 Photography Industrial radiographic films (roll and sheet) and metal intensifying screens Dimensions 1Scope This International
17、Standard specifies the preferred and recognized sizes and cutting dimensions of industrial radiographic roll and sheet films and metal intensifying screens. It also specifies package markings. The shaping of the corners of screens is not specified. 2Normative references The following normative docum
18、ents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encour
19、aged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 1:1
20、975, Standard reference temperature for industrial length measurements. ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications. 3Conditions for measurement of dimensions The dimensions and tolerances specified in this International Standard apply at the time of manufacture
21、, measured under atmospheric conditions of (23 ? 2) C and (50 ? 5) % relative humidity, as specified in ISO 554. Dimensions may be altered by a permanent shrinkage due to aging and by a temporary shrinkage or swell due to changes in moisture content or temperature. Normally, dimensionally stable pol
22、yester base is used for these film products, and there should be no departure from the specified dimensions by more than 0,05 % greater than the maximum dimension and ? 0,08 % less than the minimum dimension at the time of opening the package. All measuring-instrument calibrations shall be conducted
23、 at a temperature of 20 C, as specified in ISO 1, and a relative humidity of 50 %. 4Films in rolls 4.1Width of rolls 4.1.1Preferred widths Roll widths of preferred sizes shall conform to the values given in Table 1. Copyright International Organization for Standardization Provided by IHS under licen
24、se with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5655:2000(E) 2 ISO 2000 All rights reserved 4.1.2General slitting and tolerance rules For rolls not shown in Table 1, the slitt
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 5655 2000
链接地址:https://www.31doc.com/p-3778601.html